pfsense

Hello, I am trying to setup Pfsense on Proxmos in a VM as router. The server have two NICs (eno1 and enp4s0). In Pfsense I have assigned eno1 to be WAN and enp4s0 to be the LAN(192.168.1.1/24) + few VLANs on the same interface. Proxmox runs on the enp4s0/vmbr0. Configuration below...

Hi all iv been learning as I go iv managed to get multiple vms running including load balancing all just for the sake of learning but iv finally hit a wall im a little scared to chance. If got my pfsense iso ready to go and im ready to pass through a Nic for the Wan but im scared if I pass the...

Nabend zusammen, Aufbau: (Modem) --- ( PROXMOX HOST: Pfsense) --- (SWITCH) --- LAN Ich habe auf meinem Heimserver zwei physikalische NICS per PCI Passthrough durchgereicht (WAN und LAN) und dort in Pfsense eingebunden. Das funktioniert auch soweit sehr gut. Nun wollte ich zu Testzwecken...

Hello, Running PVE 7.1-8 (3 Node Cluster) I'm looking for the best method of getting pfSense failover for my situation. I've tried just about every configuration I could Google up and can't get it working. I'm hoping someone may have an idea of what I direction I could go. I only have one...

"Hallo" an alle, die diesen Post lesen :) bei dieser Anfrage um Hilfe, geht es um meine Herausforderung mit IPv6. Vorweg: ich bin leider kein Netzwerk Profi. Versuch mit der Materie aber so gut wie möglich klar zu kommen. die Herausforderung: IPv6 IN den VMs und Containern zu nutzen. was habe...

Hi All, Hoping someone can tell me the obvious thing that I'm missing! I'm running dual Chelsio T520-CRs in a Dell R620 with PVE 7.1. I have a pfSense VM on the host and am passing through the T520's. All works fine if I pass through the whole card, but if I pass through an SR-IOV VF...

I'm trying to hunt down a network throughput issue I'm having in my virtualized environment. It was suggested that perhaps my OVS config could be to blame and so I wanted to get a sanity check on what I'm working with. X-post...

Here is my setup: WAN -> Server (Proxmox host) IP 10.0.0.x -> pfSense ip 10.0.0.x (VM on Proxmox host) > switch ip 192.168.1.x I would like to put my Proxmox host behind the firewall. Is it possible? Is it a good practice? Is it the good way to do it? I am new to this and I need your help...

Guten Abend Zusammen, ich bin gerade leider etwas ratlos, da mein VLAN auf meine Proxmox-Host nicht funktionieren will. Zur Erklärung: Ich habe 1 Switch (TP Link TL-SG105E) im Büro, wo mein PC steht. Dieser befindet sich am Port 3 des Switches mit VLAN 20 (untagged) und der PVID 20. Von hier...

I am new to Proxmox and would like to run pfsense virtualised in PVE. I have an Intel i350-T4 NIC (currently using only enp2s0f0 and enp2s0f1) and onboard ethernet Intel I219-V (eno1). I was able to install pfsense VM sucessfully by following the guide in the link...

Hello, I'm trying to learn how to host a website from a virtual machine. I currently have a pfsense dedicated computer that runs my routing / firewall. Connected to that is a managed switch with no additional configurations currently. Connected to that is a rack server 2U Proliant G8 with...

I was forced to switch my router/firewall since my old one couldn't keep up with the speed. So I did my research and pfSense was what seemed to be a great choice, I found this in their documentation: https://docs.netgate.com/pfsense/en/latest/recipes/virtualize-proxmox-ve.html and set up the...

Hallo, Our connexion to the the internet will be switched to fiber this week. Our ISP requires VLAN10 and PPPoE and I’m a bit confused. I’ve installed Proxmox for the first time this weekend, reinstalled pfSense and this works fine.LAN and WAN have physical interfaces on the Proxmox box...

Hello I looking to do this. I am not sure what kind of network I have to use in proxmox. Bridge or Bond or..... ... ?

Hy people I ran into a problem. First of all, some information on the side: I know how PCI passthrough works under Proxmox. All parameters and modules that are required on my hardware are set and loaded. The device is already unmounted using a script and a cronjob during the start of Proxmox...

Hy Leute Bin auf ein Problem gestoßen. Erstmal gleich ein paar Infos am rande: Ich weiß über die Funktionsweise von PCI Passthrough unter Proxmox bescheid. Alle Parameter und Module die auf meiner Hardware benötigt werden sind gesetzt und eingeladen. Gerät wird anhand eines Skripts und eines...

Here's what I have: Proxmox installed on a very powerful machine (RAM/CPU-wise). I have granted generous amount of CPU + RAM to pfSense guest. Now I have a 10gb uplink 9000 MTU connection for WAN. It's fiber / SFP+. I am doing full PCIe passthrough. (all functions of card selected, PCIe...

Hello i am going to create new server on Proxmox and as 1. VM is going to be PF Sense other VMS should be connected to pfsense on VLANs can you help me how to configure and how add physical connection Wan from proxmox to PFsense VM and from pfsense virtual network as lan for other VMS?

My config is this: 2 Clustered Nodes Open vSwitch Virtual pfSense for vlan segmentation Hypervisors NET: PVE #1 eno3 (vmbr1) directly connected to PVE #2 eno4 (vmbr1) VM Network: PVE #1 eno4 (vmbr2) directly connected to PVE #2 eno3 (vmbr2) My goal: I want to create a separate VM network...

Hello, I have installed proxmox 6.3-2 and works great with 5 VMs (one of Pfsense). All of VMs connects the internet and proxmox web gui without any problem. But proxmox can't, even cannot ping 8.8.8.8 from proxmox shell. Got 4 ethernet on my server, using 2 of them and configured like as...