pfsense

PVE 7.2-3 Per my title, my VLAN tagged VM's can only pull a DHCP address from the router when the gateway the bridge isn't set. Since this is a shared bridge, the hypervisor can't reach the internet for updates etc. Any help to fix this is greatly appreciated! My home network is running a...

100% Grade A Certified, Grass Fed Noob here, so please bear with me. Background I got a server, installed Proxmox, can access Proxmox with Nic #1on https://10.0.0.163:8006/ when I connect it direct to my PC. I then installed pfsense and assigned Wan on Nic#2 and Lan on Nic#3. Seems to work...

Hi, i am restructuring our proxmox cluster network and i have some doubts and requests for suggestions that i expose below My scenario is as follows (1) two public IP ports (untagged vlan) on different servers (2) seven ports (tagged vlan) (3) I don't have direct access to the switch of (1)...

I don't have Proxmox and PfSense experience, but have watched a couple of YouTube videos about setup. Wonder if I can get any opinions and guidance from anyone with more experiance on a small self-hosting web hosting solution I’m imminently looking to setup. Networking Modem -> PFsense Box ->...

I don't have Proxmox and PfSense experience, but have watched a couple of YouTube videos about setup. Wonder if I can get any opinions from anyone with more experiance on a small self-hosted web hosting solution I’m imminently looking to setup. Networking Modem -> PFsense Box -> Managed Switch...

Hello, I have rented a dedicated server. I have proxmox installed on it. Now I want to use pfSense as firewall and for internal routing of the other VMs. My goal is to: - An IPv4 for the host on which proxmox runs and is callable on the internet over it. - An IPv4 for the VM of pfSense, so...

Hello, I am currently on a project in graduate school and here are my tasks that have been assigned to me: - To study, propose and configure a Linux server allowing to propose the DHCP/DNS service under a Proxmox VE environment. - Study, propose and configure a router / firewall / NAT...

Hi, I would like to set up a virtual pfsense vm to act as a firewall for several separate networks. There will be a trunk port feeded into the proxmox host (say eth3) with several vlans defined on it. (note that the proxmox mgt IP is not on those vlans, it's on a different one and is on a...

Hi, I have an old TS140 with 2 NICS both speed is 1Gbps, the server got 14GB DDR3 RAM, and i3 4170 CPU, internet speed is 500/20. I installed proxmox on it, 1 Windows server virtualization, and 1 for nat/firewall/dhcp/dns called zeroshell. Upload speed just works fine, but download speed is...

Hi all! Short question: what is the best way to how to add other IP address for Public IP (Internet vmbr0) on Proxmox 7 ? Further information about this question: My PVE PROXMOX v7 is using one vmbr0 for external public IP Internet access. This one is linked to eth0 physical network card...

Dear all, Last weeks I've spend many hours/days for searching a solution to my problem: IPFO declaration with PFENSE VM architecture.... As shown in this picture above: OVH MAIN IP/FAILOVER -> VMBR0 --> VMBR1 (WAN) --> PFSENSE (WAN) --> PFSENSE (LAN) --> VMs ... and I don't know/understand how...

.

Hello, I have two onboard NICs connected to my network. No VLANs for now. I have both connected to a pfsense VM with bridges. ISP router is on 192.168.2.1 with DHCP disabled. It appears that one NIC does not have its own MAC address and copies the other? This causes my console to be flooded...

Hello, ProxMox community, The problem I have recently purchased a Converged Network Adapter (NIC) Intel 82576, and I am having problems setting this up. When I start up Proxmox, the computer isn't connecting to the internet. When I am in the BIOS, the NIC lights up as it's receiving data but...

Hello, I am trying to setup Pfsense on Proxmos in a VM as router. The server have two NICs (eno1 and enp4s0). In Pfsense I have assigned eno1 to be WAN and enp4s0 to be the LAN(192.168.1.1/24) + few VLANs on the same interface. Proxmox runs on the enp4s0/vmbr0. Configuration below...

Hi all iv been learning as I go iv managed to get multiple vms running including load balancing all just for the sake of learning but iv finally hit a wall im a little scared to chance. If got my pfsense iso ready to go and im ready to pass through a Nic for the Wan but im scared if I pass the...

Nabend zusammen, Aufbau: (Modem) --- ( PROXMOX HOST: Pfsense) --- (SWITCH) --- LAN Ich habe auf meinem Heimserver zwei physikalische NICS per PCI Passthrough durchgereicht (WAN und LAN) und dort in Pfsense eingebunden. Das funktioniert auch soweit sehr gut. Nun wollte ich zu Testzwecken...

Hello, Running PVE 7.1-8 (3 Node Cluster) I'm looking for the best method of getting pfSense failover for my situation. I've tried just about every configuration I could Google up and can't get it working. I'm hoping someone may have an idea of what I direction I could go. I only have one...

"Hallo" an alle, die diesen Post lesen :) bei dieser Anfrage um Hilfe, geht es um meine Herausforderung mit IPv6. Vorweg: ich bin leider kein Netzwerk Profi. Versuch mit der Materie aber so gut wie möglich klar zu kommen. die Herausforderung: IPv6 IN den VMs und Containern zu nutzen. was habe...

Hi All, Hoping someone can tell me the obvious thing that I'm missing! I'm running dual Chelsio T520-CRs in a Dell R620 with PVE 7.1. I have a pfSense VM on the host and am passing through the T520's. All works fine if I pass through the whole card, but if I pass through an SR-IOV VF...