pfsense

Hallo auch! Ich habe aktuell das Problem, dass meine VM's keine Verbindung raus zum Internet haben. Ich habe 2 Linux Bridges sowie IPTables/NAT konfiguriert! vmbr1 für die Kommunikation zwischen ProxMox und PfSense 10.0.0.1 vmr1 => 10.0.0.2 WAN (PfSense) - Die Weboberfläche erreiche ich daher...

Hello there! I got a problem that my VM's dont have any connection to the internet and i don't know why. I have setted up 2 Linux Bridges and IPTables/NAT is configured vmbr1 for communication from ProxMox to PfSense 10.0.0.1 vmbr1 to 10.0.0.2 WAN (PfSense) - I cannot access the Webinterface...

Hi, I would like to know if my setup below can be configured to work (sorry for my badly drawn schematic). For the past two weeks I've been struggling to setup pfSense. Every time I turn on the pfSense VM, my connection to Proxmox drops. My idea is to pass WAN traffic via Vlan 10, filter it...

Hi, I'm not so experienced in the networking part. I have a PC on which I installed Proxmox, which has only one entry point for a network cable (so only 1-NIC). The vmbr0 interface is used to be "port/slave" of the actual network interface. I have defined several VMs / LXCs in Proxmox, that...

Hallo! Ich bin (wie offenbar viele hier) noch recht neu in virtuellen Umgebungen. Ich möchte meine komplette Rechnerstruktur auf Proxmox aufsetzen und das gesamte Heimnetzwerk über pfSense routen bzw. absichern. Ich bin aber unsicher, was die Adressvergabe (siehe Beispiel PDF) angeht. Wäre das...

Hello, First of all, this is my setup: I have a server at Hetzner with 2 public IP addresses. One for Proxmox and one for the OPNSense. My /etc/network/interfaces looks like this: # network interface settings; autogenerated # Please do NOT modify this file directly, unless you know what #...

I have a new NUC7i5 with 32mb memory and 1tb storage and I think/hope Proxmox is the key to what I want to do. The hardware limitations I'm concerned about: one graphics adapter with one display (my TV) and one ethernet port. I would like to run the following on the NUC: 1) home assistant...

Moin zusammen, ich habe ein Problem, bei dem ich offensichtlich nicht weiter komme und eure Hilfe benötige. Ich habe einen Proxmox-Node, auf dem eine pfSense virtualisiert läuft. Proxmox hat zwei physische Interfaces, einmal das WAN-Interface, welches ich in die pfSense durchreiche (über eine...

My problem: IPv6 connectivity on the Proxmox host appears to be working fine, I can make connections to and from the Proxmox host, for example, SSH (over IPv6) into the host and pinging the Cloudflare IPv6 DNS address works fine, but that's as far as I can get. Connections from the pfSense guest...

i accidently added a router to the same nic which i was using to access proxmox and the router is setup on auto start on boot i have tried everything and now the screen is stuck on destination host unreachable ping i am not able to login through the tower physically or access the web gui page...

Hallo, ich habe das Problem das ich bei einem VLAN Netz, welches ich erstellt habe, keine IP zugewiesen bekomme. Ich nutzte eine pfSense Firewall die auf meinem Proxmox läuft. Ich habe ein VLAN 10 auf der pfSense und auf dem Cisco Switch erstellt. Das VLAN 10 soll für Gäste sein. Auf einer...

Hi all! I have been trying to fire up my VM for pfsense firewall(v2.5 community edition). That requires me to assign two network interfaces to the VM. I bought 4 port NIC card (Intel PRO/1000 PT EXPI9404PTG2L20 LP Quad Port Adapter 10/100/1000Base-T PCI-E). When I go into VM>Hardware the setup...

Hallo Forum, ich habe ein Root-Server bei Hetzner und Proxmox VE installiert. Ich habe dort zusätzliche einzelne IPv4 Adressen, leider bekomme ich es nicht hin, diese auf die pfSense VM draufzuschalten, umzuleiten oder sonstiges. Ich möchte innerhalb der pfSense-VM dann ein 1:1 NAT mit der ggf...

Hello everyone, I am trying to isolate my Proxmox network from my home network in the safest way possible. I have tried some arrangements as shown below but the end result is exactly the opposite of what I wanted. Currently, everything connected to Proxmox network and through Pfsense can ping my...

Hi, I plan to install Proxmox on my home server and then have at least 3 VM's one PFSense, one for TrueNAS and one for services. I only have the single HW NIC that comes with my motherboard that has 4 Ethernet ports. Is it possible to configure Proxmox so that the input from the Modem goes...

Dear Forum I want to run pfSense in Proxmox with a FO IP and given MAC address. I gave the VM the name 'pfsense', entered the given MAC for vmbr0. vmbr0 for WAN and vmbr1 for LAN. Following network configuration: =========================================================== auto lo iface lo inet...

I am running the latest pfSense (2.4.5 p1) I have a fiber gigabit connection to the internet and my nics are 1gb. When I install Suricata and turn it on It reduces my speeds to 280mb/s. That is a 72% drop in speed. I have turned off the detection rules, changed the modes, and none of it changes...

Hello, i have installed proxmox and the current configuration is the default one, so one ethernet port eno1 and one linux bridge vmbr0 which has as bridge port set to the interface eno1. The public ip address is setup on the bridge. i can reach the proxmox interface on the public ip address. I...

Hi, I installed pfSense as vm according to this tutorial https://docs.netgate.com/pfsense/en/latest/recipes/virtualize-proxmox.html#:~:text=on the host-,Basic Proxmox networking,eth0 is for Proxmox management But the NIC that is bridged to the vm is down, even if I use to command ifup eno1...

I have a pfsense VM running on proxmox that handles Internet and routing. Proxmox is configured with dual NIC (one LAN, one WAN) and two linux bridges that are tied to the specific physical interfaces Internet / pfsense works just fine until I want to use the internet on the proxmox server...