network configuration

I have a Dell PowerEdge T430 that I'd like to set up as a Proxmox host. I intend for it to be my router, among other things. Since I want the pfSense VM to be the gateway, I've set it up without connecting it to my modem, but now I can't connect to the web GUI. It just times out. I'd appreciate...

Hey Everyone, looking for some advice as im busting my brain. I have this 6 port pc initially i thought i could setup pfsense on it with 1 port Wan and other 5 LAN being able to assign same vlans to multiple ports. but turns out pfsense only lets you assign vlans to 1 port by restrictions. Now...

Hi, I'm pretty new at this, managed to get a proxmox server up and running at hetzner using zfs raid1 and efi boot (took a while) Now trying to get the basic network config right for a single IP setup allowing me to setup an use virtual machines within my network. I tried a script to automate...

Hello, this is my first time configuring server and things like this. I was able to get address from DHCP server and now I can ping gateway. But still can't link outside of network or any other PC in room. I can ping server from other computer. eno1 should be my working interfaces (I hope so)...

Hey, I'm new to the area and wanted to find out if it's possible to configure it like this :) I plan to get a dedicated server with 2 IPV4 addresses and a /64 IPV6 subnet and wanted to ask if it is possible to assign an IPV4 to Proxmox, give one to a VM and give all other VMs an IPV6. Since it...

Hi, first off, sorry if this is in the wrong category. I am kinda new to Proxmox and Linux in general but find it really useful, so I started tinkering a bit. I have a Windows 10 (main workstation) and a "home server", an E5-2678V3 on a dual socket Chinese board. My server is running a TrueNAS...

Hi all, recently i've ordered an auction server from hetzner and wanted to run all my vps-vm needs on this auction server. I've followed so many tutorials, applied so many rules and re-installed proxmox so many times in the past week. Anyway, my problem is getting networking done. To be honest...

Hi, I have set up a LXC / Container to use with Docker. As I am using VLANs in my network, I am using the following configuration: $ ip route show default via 192.168.60.1 dev eth1 onlink 172.17.0.0/16 dev docker0 proto kernel scope link src 172.17.0.1 linkdown 172.18.0.0/16 dev...

I recently moved my server from one location to another and plugged it in, It runs just fine, I have no internet and can not ping in or out of proxmox and no ability to access the web ui. The virtual machines inside of proxmox that start at boot both have internet access and I can connect to...

Hello ! After moving, I had to switch router. My IP-Range changed and I couldn't fix it through the router, so I had to change id through Proxmox. The weird thing is, on my router interface, I only see one VM showing up, and it's not proxmox. And I can't access promox through the UI (using the...

Hi All, I already have setup LACP between my Cisco Switch and the Dell R720 running Proxmox. This LACP is VLAN aware and can carry VLAN20,30 etc. traffic. I also have some spare NICs on my server and on the Cisco switch, therefore, I now want to setup Security Onion. This is what I want to...

Hi, I am a newbie here so apologise first if this has been discussed previously. I recently installed Proxmox VE 7.2 on my old laptop in the hope of turning it to a home server. However, I cant reach the proxmox page on my webbrowser via the ip address generated after installing it. The ip...

Hi there, I have Proxmox 7.2-4 running on a Dell R520 with a 10G connection Unify switch 1-2. The 24-POE switch is connected with a 10G connection to the UDM - Pro Router. I wanted to give access to the Jellyfin content (on a ZFS dataset on the same R520). Pihole and Traffic provides the Https...

Hallo Zusammen , ich bin echt seit mehreren Tagen und Nächten am verzweifeln mit meinem neuen HomeLab. Obwohl ich viel hier und im Netz mich eingelesen habe, geht es in meinen alten Schädel nicht rein :( bzw., bekomme ich das als Newbie nicht umgesetzt. Daher bitte ich einmal um Eure...

I attached a Plugable 2.5Gbe USB adapter to my Proxmox install, my goal is to assign it to VMs and get the higher throughput and also to use it for backups/restores to my NAS. They are attached to a 2.5Gbe switch. I can't seem to get the drivers working on Ubuntu, I installed the Realtek 2.5Gbe...

Hello! For a project we have a UniFi 24 Ports switch (2nd gen), we also have a Proxmox cluster. We configured the UniFi switch to mirror the uplink (trunk) port to the UniFi UDM. When physically connecting a laptop and Wireshark to this mirror port, we can see all traffic (from ALL vlan's)...

im trying to setup a network bridge between my 10gbit cards so my computer has a network card with 2 10gbit ports that i want to set up as a bridge in windows to effectively get "20gbit" between proxmox and my pc. proxmox server is behind my computer. so i have 2 10gbit in main pc going to...

pve 's gateway is 192.168.5.1 , the vm(arch and linux) use the host 's gateway by default. I want to change the vm's gateway. But after changing the vm's gateway by using "ip route", the gateway will be reset to 192.168.5.1 after rebooting.

I have a problem where the vm(s) i create are not able to connect ot the internet i use a dedicated server from hetzner the vmbr1 - * are vlan tests that aren't connected to the vm(s)

Hi ! I'm working on installing and configure some proxmox homeservers using Ansible. I have 2 playbooks : First install Promox over Debian Second set-up networks by writing in /etc/network/interfaces Between playbooks, Proxmox GUI show correctly some networks. After the second playbook and...