network configuration

Hey, I've just installed Proxmox VE 8.0.2 on two different types of PC and I'm having the same issue. They both are stuck on 100Mb/s network speeds, not sure where to go from here. I did fresh install's just last week and made sure they are both up to date. root@TestLabServer:~# ethtool eno1...

Hello guys, I have 3 old Lenovo Office PCs running as Proxmox Hosts. All 3 of them have been updated to Proxmox 8 and worked fine. I haven't been using the 3rd node for a while and after that I wanted to boot it up again it wouldn't come online. Wake on LAN worked and after checking and trying...

Hello, I am renting a dedicated server (with multiple NICs) from a non-profit hosting provider. I installed Debian 12 and then PVE 8.0.4 on the server. They provide me with an IPv4 range (foo.foo.foo.240/29), and I use one of the addresses (foo.foo.foo.243) for the PVE node. Additionally, I...

Hello proxmox-community, we encounter a high error rate (errors, drops, overruns and frames) on the cephs network interfaces on our newly set up four-machine proxmox 8/ceph cluster when writing data (e.g. from /dev/urandom to a file on a virtual machine for testing). bond0...

Hi All I have a machine have 100Gbps network card , and I install the proxmox on the machine .When I provision a VM with VirtIO (paravirtualized) network interface ,found I can only get around 20~30 Gbit/sec network speed. Is there any way I can improve my network speed to 100Gbps ?

Hello, I would like to know how the ifupdown2 and OvS implementation in proxmox works because on a VM of my pve, I have a trunk that comes from the OvS of my PVE but when the VM is restarted the OvS service requires a restart for the flows to work whereas when I restart the pve it works...

Good morning everyone. I am completely new to Proxmox and have read dozens of threads and am still having issues. I installed Proxmox 8 on a new SSD in a mini-PC (MULTIPLE times) but I am not able to connect to the UI or even have my router recognize that the PC is connected to the network. I...

So i have snort on a vm in proxmox, it is correctly set up and in the vm's terminal i enabled promiscuous mode. But snort only is capturing and alerting with network traffic that is communicating with this machine? I think through proxmox i need to make changes to the network interface and force...

Hello All, As I have done other things in my professional carreer, I have missed some chunks of the IT, unfortunately also bigger chunks. Now working on my project I am in the middle of nowhere, exposing the ip of the management to internet. I am setting up one DL380 with Proxmox, 128 GB RAM...

Hey all, I have a DL gen10 server that I installed an HPE dual 10Gb 560FLR-SFP+ Adapter into. I've found that it will not pass bond0/LACP communication. An Intel X520-T2 with the same interface bond0/LACP config connects without issue. The switch shows LACP is communicating/connected. Does...

So, here is the thing. I have a dual SFP+ NIC that works well. I also wanted to place a 2.5Gbe Quad card into my proxmox machine. I am simply trying to do a Linux bridge within proxmox. The card is seen but won't become active. I tried a dual 10Gbe card and it was seen and would become active...

Hello, gurus!!! Please help me to understand if my required configuration is feasible. Current config: PCI shelf with one installed G25A - EMBEDDED SINGLE BOARD COMPUTER. According to G25A docs - there are 3 ETH ports on the front, indeed the LAN cable is connected to the upper ports and it's...

I had a working PVE node in a cluster on a NUC11TNKi3 NUC w/ 32GB RAM and a 2TB nvme drive. I removed the nvme drive and stuck it in a NUC10i7FNK w/ 64GB RAM. I have confirmed the NUC10i7FNK works with a fresh install of PVE but I need the existing nvme. The NICs leds don't blink (no link and...

After apt-get update apt-get dist-upgrade Did the following to get things rolling again, just posting this in case someone else runs into the same. If I should have done something differently, please let me know! Solution: In file: /etc/network/interfaces, changed two lines where enps0...

Hi everyone, quite exhausted at this point. I have a 2018 Macbook pro laying around collecting dust. And no one will buy it from me, considering what a crappy machine it is by today's standard. It has 32GB RAM, a radeon Graphics card and a 2.9 gigahertz processor. I figure this would be a great...

Hello This is currently my network configuration. I am using my public ip .116 for my PVE e, another public ip .118 as a NAT network for my VMs. The public ip .118 is connected to the firewall as WAN and the firewall then controls all the traffic. Now on the firewall I would like to also add...

Good evening everyone! I have a production cluster with 5 nodes. All of the nodes have one network card with: A dedicated public IP address on eno1. A vmbr4001 bridge for the public subnet of the guests (LXC). A vmbr4002 bridge for the private subnet of the guests (LXC). A vmbr4003 bridge for...

Can you please help me whats wrong with windows VM i created on proxmox? it's showed no valid ip on network and no internet. I already install all virtio drivers and qemu agent. already created linux bridge on vmbr0. But i confuse why VM assigned different ip address on ipv4 instead of vmbr0 i...

Hello Forum I have searched the forum for an answer for about a month now, but I am unable to find one, or a similar solution to my problem. Recently I made the decision to migrate to Proxmox as hypervisor after using VMware since 2012. It goes very well. I’ve got an LXC container running and...

Hello. Is it possible to change Native vlan to something else than 1? If so, just globally, or is it possible to make it per VM?