ssd

Was looking for some advice. I am going to be setting up Proxmox VE using this Super Micro AS-5019D-FTN4 with an EPYC-3251 processor. Initially, I was going to setup using Intel D3-S4610 960GB Hard drives in ZFS Raid1. My old setup with servers setup on Bare Bones with Windows Server 2016...

Hi, We're running proxmox 6.0-4 on a couple of HP DL360ps, with HP 220 HBAs, and four Intel S3520 Series 960GB MLC SSDs in each. The four SSDs are in ZFS RAID10 for VMs to sit on, while we have two mirror ZFS 146GB 15K SAS drives for the OS. We're getting some uncomfortable feedback from the...

Hello everyone, i have question about my Proxmox VE. First details about my system: OS - Proxmox VE 6.0 updated Hardware: CPU - Ryzen 1700x, RAM - 32GB 3200 nonECC, SDD - nvme 512(system is on it +20% overprovision) SSD - SATA 3 256GB HDD - 2x2TB ZFS mirror lz4(for storage), HDD - 2x1TB ZFS...

Hi, I’m thinking of replacing the single SATA SSD (500GB Samsung 860 Evo) disk in one of my PVE6 cluster nodes with a 500GB Samsung 970 Evo Plus NVMe disk... Should this simply be a case of using clonezilla to clone the SATA SSD to the NVMe and then booting PVE6 from the NVMe or would there...

hii all. i am in the process of getting new hw and go to ceph storage i think my hardware will be based on 5 nodes each with with 3x pcie-nvme and 10x 2.5 ssds each the ssds 2.5 will be used for mostly read intensive access and the pcie-nvme will be used for os\sqldb and lxc containers...

Hi, i have right now old two 500gb HDDs (raid 1 setup) and i think later to replace then with two or three ssd as raid 1 also. How i can do it, for system is understand that replaced one for system to mirror and not as a free memory.

Hi all I'm new to Proxmox since a few months for a home server. I started with a single HDD to get familiar with the system but now I would like to reinstall the system and reuse my VM's and containers already installed. In particular, there is 1 windows VM + data which I would like to keep...

Hi, I have a simple question which I would like to share with because I’m interested in you point of view. On a Proxmox server I have fast storage (SSDs or NVMe) and slow storage (SAS or SATA). My fast choice could be to install Proxmox on fast storage and use it also for storing virtual...

Hi all, we have a production running cluster of 4 nodes version 5.4 with CEPH over SATA disks, 4 monitors, 1GB/s network cards. We have purchased 4 new servers, all with SSD's and 10GBe NIC's. As at least half of the containers and VM's on the existing SATA cluster will have to be migrated to...

Hey Guys! First of all huge thanks for the support. This forum is a great help with any issues I have encountered so far.. I need some guidance with storage setup in my proxmox node... Current setup: -4x2tb SAS hdd (RAIDZ2, holds roughly 1TB of data now) -100gb consumer grade ssd SSD holds...

Hi, i am new to Proxmox VE. I've put 4 x 1TB nearline SAS drives in a Dell Precision T5500 on a PERC H200 and installed the pve on them in RAID10. I feel them a little slow and want to accelerate them with PCIe SSD accelerator SUN F20. The Prox sees 4 x 24GB SSDs and i want to use 2 of them in...

Hi all, I would like to improve performance in my second pool 3x1TB HDD RAIDz1,I want to lower I/O delay its not high but I was reading also that there shouldn't be any I/O delay, (first pool where is Proxmox I have 2xSSD in RAIDz) by adding SSD drive as cache. I found already on Google some...

Am excited about learning and using ProxMox with ZFS and to this end recently bought a DELL PowerEdge R710 with 96GB Ram, 6x1TB Drives (Hitachi Ultrastar HUA721010KLA330), 1xDVD drive, a pass-through HBA controller for ZFS, and an iDRAC6 Enterprise Mgmt module. I've updated the R710 to latest...

Hello! we have 2 servers with local ZFS pools. The pools are configured with the same type of disks. They have 3 x 120GB SSD and 4 x 4TB HDD. I set the 3 SSD as a physical RAID 5, there runs Proxmox on one partition and ZFS logs and cache on 2 other partitions. Then, with the 4 HDD I set up a...

Hi all, I'm hoping I can get some insightful input from this community. I'm looking at building out a new Proxmox cluster with Ceph as the backend. I'd like to get a couple of answers to see if this makes sense and if not where I should make changes. http://bit.ly/2XvgrXa Its a 2U 4 Node...

Hi guys, Need help to get best performance for my server. - DELL PowerEdge R820 - CPU : 4 x 2.60Ghz E5-4650L Xeon Eight Core - RAM : 12 x 16GB PC3L-10600, [192GB Total] - HDD : 8 x 960GB SSD SATA 2.5" 6GB/s (Samsung PM853T) - RAID : PERC H710 (I ordered a H310 since H710 doesn't support HBA or...

We're planning on using a few Intel NUCs in lab conditions with Proxmox. They take a single M.2 NVME device. What would be the best filesystem to use in this case? Also if ZFS would a RAID1 or RAID0 array be the correct option?

We're evaluating Proxmox in our lab and have two setups - both running 5.3: 1. Xeon Storage: ZFS (10x 3TB SAS + 100GB ZIL SSD) 2. i7-7700K Storage: ext4 LVM (1x 1TB SATA SSD) Running the following sysbench commands inside identical LXCs to evaluate storage performance: sysbench...

Hello! I would like to ask for some advice here what type of installation and configuration setup do you guys recommend for this 2 systems: 1. System 2xE5-2670V2 64GB RAM 1x1TB NVME SSD and 1x128GB SATA SSD for Proxmox 2. System 2xE5-2696V2 128GB RAM 2x1TB NVME SSD and 1x128GB SATA SSD for...

Hallo zusammen, ich teste gerade eine Konfiguration mit Proxmox VE 5.3-8 und habe ein Problen mit zwei NVME SSDs. Die Grundinstallation hängt an zwei SATA SSD Platten auf denen ich zuerst die virtuellen Maschinen getestet habe. Hierbei gibt es auch keine Probleme - jetzt wollte ich noch zwei...