help

Ich habe seit ein Cluster (3nodes) auf 10gbit umgebaut. Dieses funktioniert soweit einwandfrei, aber irgendwie kommt es in einem speziellen VLAN zu komischem Verhalten. Ich habe jetzt schon mehrere VLANs auf px1 erstellt z.B. vmbr1.30 (10.30.1.1/16) und sobald ich von einer vm mit z.B. eth1 -...

I just want to remove a snapshot and some other volumes, but I get this error: WARNING: Not using device /dev/sdc3 for PV dZEj9H-iMci-6qmy-bC40-7oXv-U3CN-krnd50. WARNING: PV dZEj9H-iMci-6qmy-bC40-7oXv-U3CN-krnd50 prefers device /dev/sdb3 because device is used by LV. WARNING: Not using...

I am having issues with the setup. I did a fresh install of PVE8 and enabled Intel IOMMU. I have everything ready to do on web interface but it does not appear on my network. I have ensured all the interfaces in the ~ip a list are presented in /etc/network/interfaces. The text file is what I...

Hello, I use a MiniPC as a proxmox backup server. I have a 2.5 inch 128GB SSD connected via a USB3.0 adapter. The operating system is installed on it. And I have an 8TB USB hard drive connected for the backups. I know this is not the best solution, but it has worked for me for over a year...

I've been at this for a week, and I can't figure it out. Sorry for the Information dump, but I'm hoping that someone can take a look at the below to both try and solve my problem, and also offer a sanity check that I'm properly using VLANS and routing in my network and within Proxmox itself...

After rebooting, one of my VMs fails to start with this message "TASK ERROR: timeout: no zvol device link for 'vm-125-disk-0' found after 300 sec found." This is on 8.0.4 and here are some outputs I think might be relevant. Any ideas how I can resolve this?

I recently upgraded to proxmox 8.0 and noticed that after rebooting, my LXC templates and VMs had been reverted to older versions. I'm not sure on the details, but things like mount points had been changed, and some instances wouldn't start due to the root disk pointing to old storage locations...

Während ich im Terminal bin kommt immer wieder dieser Error auf und das Terminal hängt für ein paar sekunden Interrupted system call (os error 4) TASK ERROR: command '/usr/bin/termproxy 5900 --path /vms/101 --perm VM.Console -- /usr/sbin/qm terminal 101 -escape 0 -iface serial0' failed: exit code 1

Greetings my friends. I wish you a good ending of the week. I have this particular question on my mind it's been a while now. On my laptop, I run a Python code that takes about 30 seconds to compile and run. My objective is to run the same code on a cluster of 3 nodes and determine how much...

I'm trying to get Proxmox up and running with this PC. It is a clone of the Minisforum GK41. This PC has two separate ethernet controllers, each wired up to one of two ethernet ports on the back of the machine. I have tried to plug an ethernet cable from either of these ports back to my router...

Hello, as you can see, below I have attached a diagram of my home network and I have some concerns. I want pfSense, which will run on a VM from the Proxmox server, to be the main router (Wan PPPoE, DHCP for all devices, to provide me with Internet for the Proxmox server for the rest of the...

Hello, as you can see, below I have attached a diagram of my home network and I have some concerns. I want pfSense, which will run on a VM from the Proxmox server, to be the main router (Wan PPPoE, DHCP for all devices, to provide me with Internet for the Proxmox server for the rest of the...

Hello. I am trying to get hw-transcoding setup for my Plex container in Proxmox 8. The following is the guide I followed: Install dkms on the PVE host via apt-get install dkms Install latest pve-headers: apt install pve-headers Download and Install the proprietary NVIDIA drivers from the...

Hi. I followed the guide https://pve.proxmox.com/wiki/Renaming_a_PVE_node, and renamed my main node, and also my cluster name. When trying to move a vm back to the newly named node, I get the error 2023-09-04 21:09:39 # /usr/bin/ssh -e none -o 'BatchMode=yes' -o 'HostKeyAlias=ravenclaw'...

So i am installing proxmox 8 and it is frozen at 70% (extracting pve-kernel-6.2.16-3-pve6.216-3_amd64.deb) its been stuck for over 30 minutes.

Hi guys, For learning purposes I just set up a virtualized Proxmox node on my Linux laptop, using virt-manager and qemu. Everything worked very well, i set up my pihole lxc etc. But when I started to create VMs and that kind of stuff it just didn want to work. When I want to boot the VM it...

Hi, we installed a new hostsystem a couple weeks ago but have some performance issues in certain vms. The hostsystem is on 7.4-15 with Kernal 5.15.108-1 and it is primarily used for game / csgo servers. We are running a Ryzen 1700x, 64g ram and 2x 1tb nvme zfs raid1. Inside the vm we run ubuntu...

so i have an issue that i've come to notice on proxmox, for some reason my system shuts itself down seemingly randomly, until manual reboot. i'm not sure if it's hardware, or some kind of watchdog setting, i had talked to someone and confirmed there is a watchdog on there, but i don't know how...

I know, this is very stupid of me.. But i decided to clean out some old VM's before starting backups (you know, limit backup size and all) only to discover that one VM actually had important data. It's a standard install with thin LVM, and i booted into a linux Live CD with RLinux. i can see...

I have ZSTD backup files in a spare SSD, and I thought I would be able to simply add it as a directory to restore my VMs when I set up a new rig, but after an hour of fiddling and looking around the internet, I can't seem to get it! I'm guessing that I don't know the proper directory to enter...