pcie passthrough

Dear Proxmox community I'm getting mad with my problem. Therefore I am now turning to the International Forum, in the hope that you can help me. I have the problem that I cannot get one of my Proxmox servers to output the audio signal via HDMI from a GTX1080TI graphics card connected via PCIE...

Hallo liebe Proxmox Gemeinde, ich beisse mir grad seit Tagen an dem o,g. Problem die Zähne aus. Kurz ein paar Infos zu meinem Vorhaben: Ich habe mir nun Proxmox auch auf meinem Hauptrechner installiert, weil ich es einfach praktischer finde in VMs mit verschiedenen Systemen arbeiten zu können...

Hello, I'm trying to passtrought a pcie nvme ssd to virtual machine. I'm not using a HBA, but each ssd is directly connected to pcie connector. I followed up: pcie passthrough guide. IOMMU is enabled and working, all required modules are also enabled. Also the nvme drive is using the latest...

Hi all, Please forgive me if I sound like nonsense. I just installed proxmox on my Alienware 15 R3 and everything seems to do good so far. But I'm in a situation where I wish to passthrough my Geforce GTX 1070 to two VMs which will definitely not run simultaneously. Is it possible to configure...

Hello, I recently added a Wi-Fi adapter (Asus PCE-AC68) to my system. I first installed the drivers on Windows 10 VM and then added the "PCI Device" from "Hardware" settings. The adapter shows up when I run the lscpci 01:00.0 Network controller: Broadcom Limited BCM4360 802.11ac Wireless...

Hello everyone, i have been trying different guides (beginners guide on /r/homelab, craftcomputing, proxmox official) with my 9700k on a Z370P-D3 running a fresh proxmox 7.0.8 to pass through my 2080ti. However, proxmox still shows “No IOMMU detected, please activate it. See Documentation for...

Hi I am running Proxmox VE 6.4-6 on a old desktop with Intel i7 - 4790 processor. I have successfully created few LXC container and ubuntu virtual machines. They are working like charm. I also have created a windows10 - pro vm and it also worked fine. Now I have a GTX 750 card installed in one...

Hey guys. I have a PCIe SATA controller that I'm trying to pass through to a Debian VM on my Proxmox node. The machine is running on a Ryzen 7 3700X in an Asrock B450 Pro 4 motherboard that I have updated to the latest BIOS with 64GB of RAM. Proxmox is installed on a RAIDZ-2 consisting of four...

When building a virtualized environment, I have an Asus Prime Z490-p motherboard (as shown in the picture) with 4 x1 pcie and 1 x16, and 1 x8 with a total of 6 pcie slots. However, after inserting the network card into the 4 x1 slots, it is found that the realtek network card that comes with the...

So I'm trying to enable IOMMU so I can pas trough a PCIe device. I've follow the guide from the documentation but in the GUI it still says: "No IOMMU detected, please activate it.See Documentation for further information.". When verifying if IOMMU is enabled using dmesg | grep -e DMAR -e IOMMU...

Hi, Did some digging but have not been able to find the solution to my issue. I know that you can easily pass disks via the PCIe passthrough. I know that you can pass on HBA controller via the PCIe passthrough exposing all disks connected. But what to do when I want to pass on zfs pool created...

hi all, I am planning to setup a freeNAS VM and pass through the relevant controller. my setup: - supermicro x10sdv-6c - 1x m.2 nvme for proxmox OS etc - 4x sata HDD to pass through to freeNAS my question now: would it make more sense to A: pass through the on-board sata controller to the...

Hello guys, I am trying to get two HDDs to passthrough via my HBA raid controller (in IT mode) to a FreeNAS VM in Proxmox. Mainboard: ASRock B550M-ITX ac CPU: AMD Ryzen 3 3200G UEFI settings: SVM Mode -> set enabled IOMMU -> set enabled. "lspci -k" 01:00.0 RAID bus controller: Broadcom /...

I try to passthrough a AMD RX580 GPU to a VM, which boots fine without the GPU. With the GPU added as an "all function" PCIe device I only get the Guest has not initialized the display (yet) message in the console. CPU: AMD Ryzen 3950X, Mainboard: Gigabyte Aorus Ultra, Virtualisation-related...

Hi all, I use for backup job "Mode: stop" scenario. All three VMs have pcie passthrough devices - network cards, one of the vm have network card and raid controller. After VM reboot and backup job star, passthrough devices can randomly not work(more often) or work normally. I can’t connect this...

Hi, I'm trying to get the virtual functions of my Intel I350 passed through to a router vm. I got the SR-IOV working, basically following this guide on reddit. I also blacklisted their module so they don't get loaded by the host (tried both blacklist and adding to vfio-pci). Everything should...

Hello, I am stuck with PCIe Passthrough. I would appreciate every bit of help. My system setup is: CPU: 2x Intel Xeon E5-2680 MB: ASRock EP2C602-4L/D16 OS: PRoxmox VE 6.0 in UEFI As far as I know the Hardware supports PCIe Passthrough. I followed this guide...

Hi all, So I've created an Ubuntu LXC Container and I've been trying to get it to access the WinTV-QuadHD PCIe TV Card that I use for Plex. My Config file currently looks like this arch: amd64 cores: 12 hostname: plex memory: 2861 nameserver: 192.168.0.6 net0...

I've been trying to passthrough an Elgato HD60 Pro to a Windows 10 Pro VM, but when the VM starts it will hang on POST or will continuously show the spinner and reboot after a while. I attempted to boot the VM into safe mode, but got the same result. There aren't any errors displayed in...

I followed this exactly: https://pve.proxmox.com/wiki/Pci_passthrough I get this error when trying to spin up the VM. kvm: -device vfio-pci,host=02:00.0,id=hostpci0,bus=ich9-pcie-port-1,addr=0x0: vfio error: 0000:02:00.0: failed to add PCI capability 0x11[0x70]@0x90: table & pba overlap, or...