opnsense

DynFi company is a Proxmox-VE partner and also the developer of the DynFi Firewall, a new, modern Open Source Firewall. Since Proxmox-VE and DynFi Firewall are very complementary, we thought that It would be nice to provide end-users with a Screencast detailing the steps required to create a...

Hello everyone, I'm not used to the forum and it's rules so very sorry if make a mistake or if my thread is not at it's right place... So I have an issue with a little pve host that is actually a sort of mini network oriented computer with 4NICs and the following CPU : 4 x Intel(R) Celeron(R)...

Hello everyone, I have looked around and did not find the one solution that fits my current setup. Maybe you can help me what needs to be done to enable the additional subnet for my instance. Here is the general network layout: I would like to use the additional subnet for several servers...

Good evening, Unfortunately I can't get IPv6 to work over my OPNsense VM hosted in Proxmox v7. My config: Freebox pop (ISP box) in bridge mode OPNsense VM on a Proxmox 7 2.5 Gbps Eth NIC for WAN Leap of 2 Eth 1Gb/s network cards for the LAN Multi-Vlan on the LAN (LAN1, LAN2, LAN3...)...

I've been running PVE 6.4 up till now on a single HP Proliant DL380 Gen8 server for my home setup. This has been working fine ever since, but now I'm busy replacing the HP with a new PVE 7.2 cluster setup based on two Intel NUC units and a RPi as qdevice. These NUC's are each connected to the...

Ich betreibe 2 mal eine OPNSense als KVM auf unterschiedlichen Servern Bei beiden habe ich das Problem das innerhalb der Opensense lediglich 1 GB Memory verfügbar ist obwohl mehr zugeordnet ist. Dies egal ob mit oder ohne balooning hat jemand vielleicht einen tip?

In the last few days I've just started recognizing I have an problem, but i'm sure it's been happening over the last 2-6 months. I have a small Proxmox server that runs OpnSense with a dual port Intel NIC as my firewall for my home internet. On systems external to this Proxmox server, i only get...

Hello, i was trying to boot opnsense but the .img file not readable by the bios or there something wrong i try nano & vga but no luck the version nano: OPNsense-22.1.2-OpenSSL-nano-amd64.img the version vga: OPNsense-22.1.2-OpenSSL-vga-amd64.img so any one facing the same issue and success on...

Noob here, trying to install either pfSense or OPNSense on Proxmox VE 7.2-3. I can install other VMs (e.g. Ubuntu, Alpine) with no problem. However, no matter what I try with pfSense or OPNSense (I have tried ISOs from both), I keep getting the same message when I start the machine, meaning I...

I'll get my homelab setup later this week and I'll use proxmox for managing VMs and stuff. One of the most important things I have to handle for my business is networking for my clients. To be more precise, unique gateways to access the internet. I have been learning networking a lot lately...

Hello all, I virtualize my firewall via OPNsense, and previously had it set up using Hyper-V core. I recently began the move to Proxmox, but have been struggling with a couple issues. Note, I am not necessarily the most experienced in networking, as most of my knowledge is self-taught. For...

I have now a proxmox on a Dell T1700 and it works very well. I have some VM connect but now I'm a little curious to maybe add a networks card with four ethernet and also use it as a firewall/router. What are the pros and cons of having a virtual router / firewall in Proxmox to handle internet...

Hello guys, as the title say's i cant't access the Web UI over an IPSec Connection. My Setup is as follows: Site-A: OPNSense VM at Home running on TrueNAS, ISP is Starlink so no static IP Site-B: OPNSense VM running on Proxmox on a Rootserver, static IP from Hoster When i try to connect to...

Hallo, ich habe vor, in meinem PVE eine VM mit OPNsense und eine VM mit TrueNAS aufzubauen. Über die OPNsense möchte ich den Netzwerktraffik der Workstations und weiterer VMs zum Router leiten und TrueNAS soll der zentrale Datenspeicher werden. Wie sind da eure Erfahrungen? Ist das...

Hi! I am using Proxmox for some time now, but still a noob trying to learn the basics. But now i am at a point where i can not proceed without help, and it concerns my PCIe NIC: It is an Intel PRO/1000 PT Quad NIC, an ultra common one i guess everyone here should know and should be supported by...

Guten Abend alle zusammen, ich habe seit ein paar Tagen mit Mac Abuse Meldungen von Hetzner zu kämpfen. Komischerweise sind die Unerlaubten Mac Adressen die Hetzner mir in der Mail zugesendet hat, Mac Adressen die automatisch durch die OPnsense erstellt werden. (siehe Bild) Wisst ihr ob man das...

Hi everybody, Sorry for my bad English (ask for more information if needed or if I'm not understandable). And sorry if answer is present on this forum, but I don't find it. I've got à Proxmox server with an OpnSense VM to control my web access by using my Freebox in bridge mode. It works...

Hey, I just want a internal (virtuell) connection between tow VMs. is it Possible to creat that without OVS (Open Virtuell switch) ? Have a nice day.

Hy people I ran into a problem. First of all, some information on the side: I know how PCI passthrough works under Proxmox. All parameters and modules that are required on my hardware are set and loaded. The device is already unmounted using a script and a cronjob during the start of Proxmox...

Hy Leute Bin auf ein Problem gestoßen. Erstmal gleich ein paar Infos am rande: Ich weiß über die Funktionsweise von PCI Passthrough unter Proxmox bescheid. Alle Parameter und Module die auf meiner Hardware benötigt werden sind gesetzt und eingeladen. Gerät wird anhand eines Skripts und eines...