vlan aware

I've put my Proxmox machine in VLAN64 and the initial installation of Proxmox with just one interface was fine. I could reach the machine and VMs and also from a VM to my network worked without issues. Then I wanted to create a bond and a VLAN aware Linux bridge. Thus I activated LACP on my...

Hello all, I am trying to setup VLANS on my Proxmox setup either by command line or using the web interface. Unfortunately i can't seem to get it functioning. All help would be greatly appreciated. Both Nic's are bridged to vmbr0. I plan on accessing the web interface on VLAN 1 and not...

Hi, i wasn't sure how to explain this.. but essentially, I have a proxmox machine with 5 NICs eno1 -> access port (vlan50) enp1s0f0 -> enp1s0f1 -> enp1s0f2 -> trunk enp1s0f3 -> access port (vlan 20) No matter what I try, I just cannot get any interface to work except for eno1. I created a...

Moin zusammen, ich habe ein Problem, bei dem ich offensichtlich nicht weiter komme und eure Hilfe benötige. Ich habe einen Proxmox-Node, auf dem eine pfSense virtualisiert läuft. Proxmox hat zwei physische Interfaces, einmal das WAN-Interface, welches ich in die pfSense durchreiche (über eine...

Hi, as the title says i'm having a problem on VMs and containers that share the host pve VLAN. If the VM goes on a different VLAN, no problem. My intention is to have a bond between eno1 and eno2 with lacp layer 2 and have one bridge so every VM goes through that bridge with the specific VLAN...

I have been using ESXI for 5 years now on a 2011 mac mini with no issues. The setup is: - Dual NIC (one on board, one thunderbolt adapter) - One NIC is dedicated to WAN - The other NIC goes to a managed switch in a trunk port that has 3 VLANS + untagged for LAN - The switch connects to a unifi...

Proxmox ve seems to support the switch of VLAN filter, that is, vlan-aware bridge switch, but lacks the complete options of vlan filter settings. Through the bridge vlan command, users should be able to set their own ACCESS port and allowable vlan id (TRUNK mode) ), this makes the bridge work...

Hello, I have an OPNsense VM running with a dedicated WAN interface (vmbr1) and the default Proxmox Linux bridge (vmbr0) for LAN. I'm trying to segregate my network like so: WAN -> My public IP VLAN 100 -> 10.10.100.0 LAN -> 10.10.1.0 I only have 2 NICs and I am trying to pass the VLAN using...

Hi, I want to achieve following task: 1) Have multiple VLANs (1000+) that are separate from each other 2) Be able to create CTs in those VLANs BUT they are not supposed to talk to each other (cross VLAN) and/or snoop any traffic that is not in their respective VLANs 3) Be able to...

Hello everybody, for the first time I just installed Proxmox and I have a few issues with VLAN's that I don't know how to solve. My router (Untangle) is configured this way: Internal LAN (10.10.10.1) + VLAN30 (Development (10.10.30.1) + VLAN60 (Management (10.10.60.1) Now on my management...

Hi all, i'm trying to add a second vNIC to my LXC containers: on my router (usg) i've created a second network against the principal with a vlan tag 10. I've configured on my switch (unifi switch) to propagate on all ports the vlans. On my proxmox node i've checked the network option 'Vlan...

I've been trying to pass a trunk port directly to a VM, however the incoming traffic does not seem to reach the bridge. My config looks like this: auto vmbr11 iface vmbr11 inet manual bridge_vlan_aware yes bridge_ports eno2 bridge_stp off bridge_fd 0 Vlan id...