vlan

So I reconfigured my proxmox cluster to put the web interface on a different vlan. My network interface is now running on VLAN20 while the rest is now on VLAN10. Here are the network interfaces configured for my 2 nodes (My second node only has a single 2.5g interface so I used Linux VLAN to...

Hi! I apologize to open up another lot-discussed-topic, at the moment everything looks to me working well but still i would like to get confirmation if my thinking is good and specific configuration is good. My effort is computer has four physical interfaces and two of them are 10g and...

Hallo zusammen, ich habe folgendes Problem: Mein Homeserver wo auch Proxmox und pfsense installiert ist hat 4 x GB Lan Anschlüsse ( PCI Karte ). Allerdings habe ich das Problem, dass Proxmox keine Internet Verbindung hat aber Pfsense in VM hat eine Internet Verbindung. Das 2. Problem ist, wenn...

I have a Pfsense running in Tyan 52 Node, In the Tyan 52 Node, It has vmbr0 connected to the 10.1.1.0/24 network which is the WAN, and vmbr1, connected to the internal switch for 10.1.2.0/24 on the LAN As you can see on the image, I have 2 VLAN running in the LAN, it works as intended in the...

Hi, I have a PVE host with a network trunk to it, that is causing me issues with VMs running on VLAN1. I know running things on VLAN1 is not ideal, but there are some legacy items that cant be moved right now - long story. The rest of the VLANs are working just fine, and the VMs there can...

Hello, as you can see, below I have attached a diagram of my home network and I have some concerns. I want pfSense, which will run on a VM from the Proxmox server, to be the main router (Wan PPPoE, DHCP for all devices, to provide me with Internet for the Proxmox server for the rest of the...

Hello, as you can see, below I have attached a diagram of my home network and I have some concerns. I want pfSense, which will run on a VM from the Proxmox server, to be the main router (Wan PPPoE, DHCP for all devices, to provide me with Internet for the Proxmox server for the rest of the...

Hi all, I'm working on my first setup at Hetzner and I can't find any examples of what I am attempting to do. I'm hoping for some insight, an interfaces config or step by step if it's available would both be very helpful! While there's plenty of instructions with regard to hosting OpnSense...

Hello, I have a "Problem". My Physical Opnsense hardware reached its End-of-Life. So I need temporary to Virtualize my Opnsense. When I import my Opnsense Config, my Network doesn't work. I now investigated and found, its a Problem with my Lagg config. Its set to LACP which I didn't get to run...

Hello, i am facing a problem implemeting my network, with aggregation and so... Its been several days that i try things on PVE and on Switch, but i keep not having the right solution :rolleyes:. Maybe someone here can have a solution!! The problem : PVE node (accessible via 192.168.10.10) is...

Hallo, ich habe eine Frage zur Erreichbarkeit eines LXC-Container mit dem Unifi Controller in Verbindung mit Proxmox und VLans. Bisher hatte ich den Unifi Controller auf meinem alten Proxmox-Server in einem LXC Container laufen und keine VLans eingerichtet. Der Proxmox Server hing am Switch mit...

I'm trying to setup `vlan 33` with a single nic on my proxmox server. I have the below configuration on my `/etc/network/interfaces` file. auto lo iface lo inet loopback iface enp2s0 inet manual auto vmbr0.33 iface vmbr0.33 inet static address [redacted]/24 gateway [redacted] auto...

In the https://pve.proxmox.com/wiki/Network_Configuration page, under "VLAN on the Host" section, "Example: Use VLAN 5 for the Proxmox VE management IP with VLAN aware Linux bridge" shows the configuration for a single NIC and it's easy to understand. However the following snippet, starting with...

I'm seeing an odd scenario play out on a test pve cluster. The three pve servers have about 50% packet loss, dropping off the net for minutes at a time, but all VMs on them remain available at all times with 0% packet loss. Here's the network config from one of them: auto lo iface lo inet...

Hi all! I recently installed proxmox on my server, and now I'm trying to get networking in order. The problem that I have, is that for a certain VLAN, the DHCP response from my DHCP server doesn't seem to end up in my VM. It does seem to reach proxmox, but there's nothing arriving in the VM...

I've tried asking on ServerFault (https://serverfault.com/questions/1134269/where-to-put-vlan-interface) because it's not strictly a proxmox question. But I received no answers, only a suggestion to post on this forum, so I'm reposting here. I have 2 x 1 Gbps network interfaces. On top of them...

Hello everyone, I just recently set up two Proxmox-Servers (Intel NUC) and joined them into a cluster. Now I want to take the next step and separate my network into VLANs. I plan to set up a pfSense or OPNsense box (in Proxmox of course) which will service the VLANs. Both systems run the...

Hello, I'm having a bit of a hard time setting up my network right now. I have an Opnsense firewall running on the proxmox server. The server is connected to a switch and I can use VLANs normally. But now I have had the idea that I would also like to assign a VLAN to a physical port directly on...

good morning, have installed Proxmox VE 7.4 I am not able to do the following configuration with OVS. I have two cards eno1 and eno2, I need them to be in LACP bonding. These cards have vlan10 as their native VLAN and others such as vlan20 for the rest.I have tried the settings in the...

I have Proxmox 7.4-4 on baremetal server - it is fed with a trunk which I have working tagged on vmbr0. Within proxmox I have an ESXi guest VM to which I wish to provide the raw trunk vmbr0. I've successfully got it working by creating entries in my config eg: auto vmbr0.172 iface vmbr0.172...