raid

Hi, I installed Proxmox 7, and I am trying to create a new ZFS using two 1TB NVME drives via the GUI. However, I get the below error: command '/sbin/zpool create -o 'ashift=12' nvme mirror /dev/disk/by-id/nvme-Sabrent_1765071310FD00048263...

I have a server I've installed Proxmox onto that has one SSD for the main system installation. I'd like to add an identical drive in a month to mirror my base install as a software RAID-1 (raidz maybe?) so I don't have any down time for when the primary SSD fails. Can this be done, and if so, how?

I configured 2 SSDs in RAID1 on my hardware controller. After Proxmox install, the RAID volume shows up as "degraded" (Fig. 1) on the controller. The SMART values (Fig. 2) reflect that one drive is being used but not the other. I had the RAID controller "repair" the degraded mirror, but that...

Hello, I would like some advice for my data raid. I have a Proxmox with 4 SSD 2TB for data. (64Go ram, Intel Xeon 3.7GHz 8 core) On this data raid I would like to put several Windows and Linux VMs. The but is : fast raid and the security of being able to lose 1 disc I started by doing a...

Hi everyone, Does anyone know how to check raid status in proxmox ve 6.2 ? Currently, our server's disk has red light color on one of the hard disk. Also, How to check if there is any error with the hard disk ? Many thanks in advance

Trying to install 6.4 via iso on a Supermicro box with an Areca 1886-8i controller but these devices are not present when I boot to the installer. All it sees is the USB stick I booted the ISO from (Ventoy). I have a 8TB sata RAID10 and and a 2TB SSD RAID5 array on the Areca card. Any thoughts...

moin, ich habe eigentlich schon viel länger vor, meinen Host mit einem fx8320 durch etwas neueres abzulösen. Da mir allerdings immer wieder etwas dazwischen gekommen ist, ich jetzt aber noch einen i5 6600k hier rumliegen habe, dachte ich mir, ich benutze vielleicht einfach den und spar mir das...

We want to install Proxmox Version 6 on an HP-Server with the following RAID-Controllers: Servers: HPE ProLiant ML110 G10 (Intel Xeon Silver 4210 2,20 GHz) HPE ProLiant DL360 G10 (Intel Xeon Silver 4208 2,10 GHz) HPE Smart Array P408i-a/2GB plus Smart Storage-Batterie HPE Smart Array P408i-p...

Hello all My proxmox VE version was 6.3-6 and running as member cluster, i set RAID 1 on my node and when i see status SSD on proxmox interface the health was DEGRADED and just detect 1 SSD on Disk Section, so i think one of my ssd was broken (the SN ssd not showed up on disks interface...

I have a new HP-Server, with a "fake" Software-RAID-Controller. So I often read that the software-raid and Proxmox are not the best friends, so I decided to install Proxmox with ZFS-Storage-Pool. Everything alright so far, but I usually used to install Proxmox on a Hardware-Raid, so no idea...

Hallo zusammen, ich habe einen Cluster, bestehend aus derzeit 2 Servern mit je 32 Gig RAM (mehr packt das Board leider nicht) und bin auf der Suche nach einem möglichst performanten Storage dafür. Ausfallsicherheit / HA ist jetzt nicht so kritisch, aber ich würde damit gerne Erfahrungen sammeln...

Hello! I bought a HP Proliant DL380e G8 server with 2xE5-2450L and 64GB of RAM. I have 4 x WD Red WD40EFAX 4TB HDDs and 2 x ADATA 240GB 2,5" SATA Ultimate SU630 SSDs. The server RAID battery has been refurbished. Here are the RAID controllers on this machine: [12:08:36][root@zoltan]:~# lspci...

Hi, I am planning to set up a new proxmox VE on a stand alone HPE DL380 Gen9 that has a Smart-Array hardware RAID controller for storing the VMs. (no SAN or NAS storage) I know I could set the controller to HBA mode, but I’d like to use the hardware raid features for easier raid management and...

Hello, I'm deploying a new cluster with 3 machines, each one having 64GB RAM + 2x512GB NVMe SSD. The VMs that will run on the cluster will use about 70-80% of available RAM, so there will be little spare RAM left (4-8 GB). I would like to use ZFS, as it's supported by Proxmox, but I'm afraid...

Currently I have all my Virtual Machines running on a Single Enterprise grade SSD disk on the server. I would like to add redundancy to limit possibly any issues with the SSD failing and losing all my VM's at once. I am considering two options: 1st option: create a hardware RAID-1 of 2 x...

Hello, it is possible without RAID Controller in IT Mode several SATA hard drives to a VM like Openmediavault? Would this work with a SATA adapter?

Hallo! Ich habe einen Server dieser hat zur Zeit nur 300GB Festplattenspeicher. Ich würde gerne ein bisschen mehr Speicher kaufen. Es würde sich auch anbieten nun ein RAID zu machen. Leider habe ich sehr wenig Ahnung von RAID Systemen. Ich weis ich auch noch nicht ganz welches RAID ich nehmen...

Hey! i am new to proxmox, and i had 2 questions! How to acces your mobo bios when running promox? How to run raid in proxmox? (raid1) thanks!

Due to some issues on the system we are considering moving from our lvm over linux raid to lvm-raid configuration. As I understand I can convert any LVM LV to thin I am assumming I can do so too with a mirrored (raid1) LV. Anyone has experience with this setup and implications I should...

Hello everyone, i have 1 Disk where proxmox is installed on and another Raid 1 mounted as /data on the host I'd like to give my 2 windows VMs read &write access to that raid / a folder on it. I'v read a few articles on sharing disks beween VMS, though it seems like there are various solutions...