pcie-passthrough

Hi I have been recently having nvme passthrough problems. I have two samsung 990 in a bifurcation card (asus hyper) These are passed through to one of my virtual machines, but recently I have been getting Unable to change power state from D0 to D3hot, device inaccessible When restarting...

Hi all, First of all, system info: root@vhost1:~# pveversion pve-manager/8.2.4/faa83925c9641325 (running kernel: 6.8.8-1-pve) root@bramley-vhost1:~# cat /proc/cpuinfo | grep Xeon | uniq model name : Intel(R) Xeon(R) Silver 4410Y root@vhost1:~# dmidecode -t baseboard | grep -A2 Base\...

I'm running Proxmox 8.2.2 with a GPU passed through to a VM. When it's booting, the image on my screen freezes right after Proxmox boots - so I can't really do anything on it, but the VM passthrough works well. Now, I've tried to insert a new PCI-E Wifi/BT card. Proxmox then boots up, but gets...

I am having problems with my TrueNas VM as the host loses connection when I start the VM with my NVME SSD passed through to the VM. The VM runs fine if I dont passthrough the SSD. IOMMMU is active and no other VMs are running/taking resources. I am very new to working with linux and VMs, so it...

I am trying to use Proxmox with an HBA for PCIe pass through (TrueNAS). I configured the BIOS according to this guide, got Proxmox to work, added my first two drives to the HBA, and could see and add data to them. After I added my remaining 4 drives, it outputs: Asmedia sm1064/116X Sata...

Hi, I`m new member on the forum, but I`m working with Proxmox for a while. I run into quite confusing problem and need advice. Below I will describe my problem and hardware on which I am working. Host is a Supermicro AS 4124GO-NART with NVIDIA DGX A100 8-GPU 40GB working on my University...

I've got a proxmox 7.4-3 server running an i7-5820K on a ASRock x99 Taichi, with a Gigabyte GT 710. The GPU works fine (I can use it to edit BIOS settings when I boot) . I've followed the steps mentioned in both this reddit post and this one. I end up getting error 43 and no display sent out the...

Hardware: ASRock j4205 with 8gb RAM, 2x4TB WD Red, crucial ssd 250gb (sata), 1gbit ethernet. Hi, I'm using proxmox on the j4205-itx board and run omv in a vm as a nas solution. I also want to have the to hdds mirrored/raid 1. As far as I understand there are four options to provide hdd storage...

Hello proxmox users! quick question about using nvme m.2 drives. I have a pcie to m.2 cardholder in my server with a total of 4 drives. I need a vm with a lot of speed. In terms of performance, is it better to pass through the whole card or is there no loss when creating virtual disks?

Hi Proxmox community! I´m having trouble trying to passthrough the use of a GPU to a Win10 VM. I´ve followed several guides, some posted on this forum and what is posted on Proxmox VE wiki along with in more general terms of how passthrough is performed from host to VM. I´m running Proxmox VE...

Hi, are there any issues with passing through a Sangoma D100 PCIe Card to a VM? It's a VoIP Transcoding card, I can't find and documented cases of it being passed-through on PVE. We want to use it on a Centos 7 VM with PVE 7.2-7. I don't want SR-IOV passthrough...

I'm trying to get Makemkv to work on a VM on my proxmox host. It didn't work by passing the disc drive to the VM from the GUI. I've read the best way to do this was to passthrough a sata controller to the VM and connect the disc drive to that. So now I'm going through this guide to setup up...

Hi all, since the last Proxmox Updates we had problems with a Win2019 Server using an Intel Optane PCIe-passthrough-device as boot volume. First we thought, it was an Windows-Update-Error, but it's not. A fresh install on a new VM of Win2019 Server runs normal till it reboots. The reboot ends...

I'm pretty stuck here. I'm using old laptop hardware, with a i5-4200U, which does support VT-d and virtualization in BIOS, but i can't get it to work, while following the tutorial here: https://pve.proxmox.com/wiki/Pci_passthrough When I try to add a PCI device to a VM, i get this message "No...

EDIT: this is the output to lscpi -v on Proxmox host: Does this mean that the kernel is still using the card? Should I also blacklist amdgpu as well? 83:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Navi 23 (rev ff) (prog-if ff) !!! Unknown header type 7f...

Hello, I'm trying to passtrought a pcie nvme ssd to virtual machine. I'm not using a HBA, but each ssd is directly connected to pcie connector. I followed up: pcie passthrough guide. IOMMU is enabled and working, all required modules are also enabled. Also the nvme drive is using the latest...

Hi, I'am new here, i hope you can help me/ give hint to be able to use a PCIe sound card inside a windows VM. Host machine: HP Proliant 380 Gen 9 CPU(s) 48 x Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (2 Sockets) Kernel Version Linux 5.11.22-3-pve #1 SMP PVE 5.11.22-5 (Wed, 21 Jul 2021 18:25:44...

Hi I am running Proxmox VE 6.4-6 on a old desktop with Intel i7 - 4790 processor. I have successfully created few LXC container and ubuntu virtual machines. They are working like charm. I also have created a windows10 - pro vm and it also worked fine. Now I have a GTX 750 card installed in one...

Hello, I'm trying to get GPU passthrough working for a while now... My problem is that when I check the "PCI-Express" checkmark the console shows "guest has not initialized the display (yet)" and when I don't check it everything works fine. When it is unchecked and Primary GPU is checked I get...

Good morning, I bought a PCie USB card to use it in passthrough with my Windows Server 2019 VM, but now I have always errre with code 10 (in the card properties) and this happened after I received a system update, can it be solved? Could it be that it is being kept busy by proxmox and this...