mirror

Hey all, I run a standalone Proxmox server which I have been upgrading in place for years. I am currently on 6.x, not having upgraded to 7 yet. It was a clean install on Proxmox 4.2 I believe. When i initially installed it, I set it up to boot from a ZFS mirror of two SATA SSD's using...

Hi, I installed Proxmox 7, and I am trying to create a new ZFS using two 1TB NVME drives via the GUI. However, I get the below error: command '/sbin/zpool create -o 'ashift=12' nvme mirror /dev/disk/by-id/nvme-Sabrent_1765071310FD00048263...

I'm attempting to set up network intrusion detection on my LAN. I plan to do this in two steps. First, setting up a SPAN port on the physical switch will will be connected to a NIC in my single-host Proxmox server, which will then be passed through to the VM in Proxmox running Ossim. That SPAN...

Hello together, I have a dedicated server with 64gib of RAM and following disks: 500gib ssd 2x 2tib HDDs no raid controller i am planning one vm with a Nextcloud installation, one Apache vm and a Game Server vm on my proxmox installation. my question is, how I should configure my disk...

Hi all, I'm going to be using 4x 1TB NVMe M.2 drives as my VM storage which I plan to run as a striped mirror. Currently, I only have two installed as I won't have the other two for a week or so. I'm eager to get going with the setup though. If I were to create ZFS mirror of the two installed...

I have an old AMD Phenom x6 PC and figured I'd tinker around with it. My disks are as follows 3x1 TB (currently in zraid) 1x2TB 1x8TB ( newly acquired and shucked from a WD black) I don't need more than 5-6TB of storage atm. I'm thinking there is a way to mirror the 3 1TBs and the 2TB on the...

Hi, I attached a disk for the root file system to have a mirrored zfs pool. Resilvering was no problem, but how can I make the second disk bootable? I am new to UEFI and do not know any of the relevant commands. The original device: Device Start End Sectors Size Type...

I have two drives in a mirrored zpool. If I add two more drives, can I stripe the two mirrors (RAID 10) online? If not only, can it be done with minimal downtime?

I was getting ready to download a turnkey linux container and realized that I was using a mirror in Germany. At the rate it was going, I wouldn't see if until several hours later. I did a little searching and find a mirror at umd.edu... I wget the container and 2 minutes later I was ready to...

Hello! About a month ago I've decided to give Proxmox-VE a try. The installation and the creation of a few test VMs went without hitches. Everything was working smooth (reboots also) until yesterday when I performed dist-upgrade to version 5.1.42. After the upgrade I had to reboot because of...

I am attempting to install Proxmox (Ver. 5.1-3) on a system with two SSD units in a mirrored ZFS array. However, the system does not boot into Proxmox, and instead, dumps me into an EFI shell. Any assistance is appreciated. My motherboard is a Supermicro A2SDi-8C+-HLN4F (BIOS Rev. 1.0b)...

Hello, i'm quite new in proxmox, and I have two server hp proliant dl380 G6 with 8 disk in raid 5 with one spare (on both). My goal is to make them the more failure tolerant possible. So I wanted to know few things: - is it possible to make them run in "mirror mode" ? Like raid 1 but for...

Hi i have proxmox 4.3 host witch zfs raidz1 pool on 2 ssd. I use proxmox host for VMs Windows OS. I have UPS backup. I have question about zfs "sync" parameter, it improve alot write performance but is it really unsafe to use ? How sync=disbaled afect Widnows VMs ? How much unsafe it is...

hi, because of a very restrict policy (PCI DSS), it isn't allowed to get access to the internet from the pve. Also a proxy isn't an easy thing to get it working with a PCI auditor in the background. For all repos we a have internal APT server for that. So my question is: is it possible to...