lacp

Greetings friends, im here for some help with my ProxmoxVe installation. I had my server DL360E G8, and this had a 4 NIC (1gb each) and i installed another PCI with 2x1GB. Im trying to get more bandwith with LACP. so my configuration is here I already installed iperf to check bandwith...

Hi, I have more than 6 NICS in my server. Is there a possibility to create LINUX BOND for LACP at the installation stage or add it after the installation for vmbr0? I tried but it says the default gateway already exists on vmbr0. Any ideas on how to achieve this? Cheers,

Hi, We have 2 servers. each of them has 2 x10G interface. We have created bond interface with 2 x10G nics and connected 2 servers. But we are getting only 10G throughput. Not 20gbps. What are we missing in the configuration? In future we can only use LACP. not other protocols, Because we shall...

Hi, I'm trying to connect my Promox machine via Link Aggregation to a HP1810 switch. For this purpose, I have configured two ports as trunk (LACP Active) in the web interface of the switch and link aggregation on Proxmox. netstat -i suggests that this is working: Iface MTU RX-OK RX-ERR...

Hi everyone, I'm running a particular scenario here I'm using three nics in total. enp9s0f0 enp9s0f1 Are bond to LACP, slaves to Vmbr1, vlan aware Should run on a 66 Vlan enp3s0 slave to vmbr0, vlan aware should run on primairy gateway --- The reason for this setup is to, mainly run on...

My configuration: Proxmox machine has 7 ethernet ports, used as: 1x - Management port 1x - WAN port x4 - LACP bond to Tp-Link managed switch x1 - Used as physical Linux bridge port I have created 2 VMs: 1) OpnSense, uses vmbr1 as WAN, vmbr0 as LAN 2) Ubuntu 20.04, uses vmbr0 as LAN Both VMs...

Hi Guys This is my very first post and having had a 5 day workout with proxmox I have found a problem mentioned all over and that is the network that does not become active on a Windows 10 VM. I tried everything to get it to work, but wait, let me first tell you what I am running: Intel NUC...

I have a spare 10G interfaces at all cluster nodes. Planning to add this interface to Ceph. What is the best way to do it? I see following choises: 1) Add an additional network to Ceph. It will mean stop a service, delete all monitors and create it again, right? 2) Just create LACP (802.3ad)...

After upgrading to version 19.5.12 of the NIC firmware from version 19.0.12 no LACP bond interface will come active. This is just a reference for those that face similar issue. I rollback to the previous version on the Dell Servers and everything came back to normal. Proxmox Software...

Hi, Please excuse my lack of knowledge I am new to proxmox and this industry as a whole. So the server I have to run has 4 gigabit nics on it and I had configured proxmox to run on just one. For redundancy purposes and wanting improved speeds I went poking around the network config. I made a...

G'day, We have 2x switches available, each with 4x 10G ports and 48x 1G ports. They're stackable, though we'd rather avoid it. At the moment, all hypervisors are routing through 1 of the 2 switches. They're going through the untagged handoff VLAN, with tagged VLANs atop. Those tagged VLANs...

Hey folks, I'm fighting with network setup, not sure if this config can work, so would be nice if you can share info or your config regarding similar setup. PVE: 6.3-3 System: HPE ML350 Gen9 Network card: HPE 546SFP+ (MLX312B) - 2-port SFP+ (part number: 779793-B21) Bridging: using OVS...

Hello, I am trying to set up our PVE node on the network and am having an issue I've been thus far unsuccessful in resolving. The node has two NIC's with multiple ports (1-4, and 5-8), which I've set up for LACP resulting in two bonds (bond0, and bond1). The goal is that bond1 (ports 5-8 / the...

Hallo, mein nächstes Problem steht an. Ich habe nun mit 4 Netzwerkkarten ein Linux Bond erstellt. Der Bond funktioniert auch. Ich kann nur den Bond nicht als Netzwerkkarte für eine VM angeben. Was fehlt noch? Ich hatte schon versucht ein vmbr1 zu erstellen und als Bridge Port habe ich den Bond...

My network has some issues. When the network traffic increases, the network connections tend to be very slow even though it's an 10GB network. I'm not sure whether it's proxmox-related or not. Example: VMx = virtual machine x VHx = proxmox virtual host x VM1 = 192.168.0.51 (E2:A9:CC:75:79:AF)...

I thought I would post this to maybe assist anybody else that has a HP Procurve 2910al-24G network switch and using 'bridge-vlan-aware' parameter in their server interfaces. I have a 3 server cluster consisting of 2x Dell R420 and 1 x R710. I converted them all recently from Proxmox 5.4 to 6.1...

Participants: two PVEs (6.1-8 ) and an old HP-2810-24G (J9021A) I want to have both failover and double bandwidth on this two fresh installed PVEs . But actually works only failover, the bandwidth is limited to 1Gbps. I am sure I am missing something, this is why I am posting here. pve1...

Hi all, I'm running a 4 node pve cluster (6-1.3) with ovs installed. All networks configured using ovs and all interfaces are LACP bonded. OVS BOND (LACP) -> OVS BRIDGE -> VMS -> Intports Recently I noticed Windows VMs using intel E1000 drivers disconnecting after some...

I'm trying to set up LACP on my Proxmox using Openvswitch, but it's not working and I'm out of ideas and googling. I have a Zyxel GS1900, enabled LACP and created a LAG-Group with the 2 ports connected to my server. In Proxmox i set up the network like this: allow-vmbr0 bond0 iface bond0 inet...

Hello. I'm looking to setup my Proxmox 5.4 cluster with 2 bonded ports for VMs/Management and 2 bonded ports for integrated CEPH storage. In looking over the Network Config docs there is a reference to running the cluster network from the bonded link requiring active-passive mode. Which one...