hi
my working proxmox on hp g9 ml 110 not work after error: x64 Exception Type 0D - General Protection Exception
I have some windows VM, and want to access their partition to get my data.
I did many try and search, but no luck.
now I boot my server with an ubuntu 22 live, how can I access my...
I have an ubuntu server vm which I'm running pterodactyl onto it (Panel for games). I had an issue with it and tried to restart the vm. The vm when offline as it should be doesn't come back online. When I look at the bottom it says status: ok tho the vm is still offline. I have not seen any...
Hello everyone,
I've been noticing that sometimes, my Windows VM's with an EFI boot on Proxmox sometimes fail to fully boot/load.
When that happens, they always get stuck on this exact same screen:
This happens on different Proxmox nodes (not clustered) with different versions of Windows...
I had a lot of ungrateful shutdowns because of regular power outages in my country and didn't notice AC Power Recovery was enabled.
When I tried to boot a machine, I faced with fsck error - Bad magic number in super-block . After e2fsck (with force:confused:) this error disappeared, but boot...
Hey everyone,
I’m encountering a bit of a snag with my Proxmox setup and could use some guidance. Here’s the situation:
I have two NVMe SSDs in my Desktop: one with Proxmox installed and the other with Windows. When I unplug the Proxmox SSD and attach the Windows SSD, everything works fine...
Hello,
Ran into a problem with my Proxmox VE. My LXC container, which is my go-to NAS, just won’t boot up after a reboot. Here’s the error it’s throwing at me:
run_buffer: 322 Script exited with status 32
lxc_init: 844 Failed to run lxc.hook.pre-start for container "100"
__lxc_start: 2027...
Hi all, I'm having an issue that happens sometimes where when I create a new VM and migrate it to another node of mine (pve12-test -> pve11-test).
VM created with:
qm create 1170 --memory 1024 --net0 virtio,bridge=vmbr0 --scsihw virtio-scsi-pci --onboot=1 --ostype l26 && qm set 1170--scsi0...
Hey,
So I am trying to install Proxmox on two Samsung 980 SSD 500GB that is on two RaidSonic ICY BOX IB-PCI208-HS.
I am running this on a Dell PowerEdge R730.
I am finding them in the install and setting them up as ZFS RAID1.
But when i am trying to boot i am only getting the error:
Booting...
Good morning, all! This is my first post here, and I'm only making it because I truly couldnt figure this one out on my own.
The other day I shut down my 3 nodes in my homelab server rack to unplug it and get all the dust behind and around it. Upon rebooting, my main node seems to have failed...
I performed a standard update on my 7.4 proxmox server to get the latest deb11 patches.
I did not see any errors during the upgrade, but after rebooting the box for the new kernel, I got this error:
Booting `Proxmox VE GNU/Linux`
Loading Linux 5.15.131-2-pve...
error: file...
Hello everyone. I'd like to ask you for help with my proxmox setup. I will first describe my story and after then the errors.
The story: Today i was about to install Hassio so i found nice script that would do it for me (my friend installed it the same way and it is okay so far). It immediately...
Anyone else run into this? Windows 11 Pro/64 on latest proxmox, installing the above update, the VM boots into windows recovery mode, none of the repair options seem to work.
Restore from backup and tested several times - installing KB5031455 causes this everytime.
Have latest Virtio (240)...
Hello everyone,
I had installed a new LSI 9207-8e a couple days ago and everything was pretty good. A number of reboots were done since the hardware install. The plan was to eventually pass it through to a VM. I had done some reading and found many saying that I should add...
Hi, I recently went through an outage and when booting Proxmox I get whats in the attachment. And is just stuck after it trying to Remount. Sometimes it gives a VGA output after next, but then stays on that too. Can't figure out a fix.
Hello,
I just upgraded from PVE 7 to 8 following the doc, the check list has no errors nor warnings.
However, when rebooting after the upgrade, I tried to login physically, I didn't have time to finish writing the password and it rebooted by itself.
Second boot I wrote the password and it...
I have a three-node cluster with PVE8 and Ceph installed. The names are pfsense-1, pfsense-2 and r730. I have been running PVE for about a year and recently installed Ceph on these nodes. It worked well, but when I reboot the r730 node, it won't boot (I waited for 15 hours). I reinstalled the...
Hi everyone,
I've been using Proxmox for a few years now and I've been extremely happy with it.
I'm making a new deployment on a Dell Poweredge r530 Server and I'm having some strange problems.
I had previously used Proxmox 7.4 with no issues at all, however a fresh Proxmox 8.0 install is giving...
Hello all, I am running a Proxmox server on version 7-1.2, few days ago i have experienced a power outage which causes system to fail at boot. When i connect a monitor to display, i saw that ZFS triggers kernel panic and system boot stucks.
After that i have booted into recovery kernel, and...
Howdy y'all.
I've had a debian 8 Proxmox server set up for a while and hosted on a Kimsufi machine. Recently (yesterday) the Proxmox web UI was no longer accessible after a reboot. I've tried booting into a rescue OS within Kimsufi to see if I can see into the lvs filesystem, but I can only...
Hi,
Last night my proxmox host shut down due to a very hot cpu. I have a new fan right now, and temperature is okay now.
However, my proxmox host doesnt' boot anymore. The boot hangs with messages like these
sd 1:0:0:0: [sdb] tag#0 access beyond end of device
I/O error, dev sdb, sector xxxxx...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.