BLUF: The onboard interfaces register in linux/Proxmox as well as an additional NIC but just not at the same time.
I have a X9DRD-LF-TW008 that I aim to use as an external server/firewall with Proxmox hosting pfSense among other things. The motherboard comes with two interfaces and an...
I am trying to change the port speed of my server port to 100baseT/Full. The port is part of a supermicro motherboard. The port is being used as a Linux bridge.
The ethtool output:
root@pve:~# ethtool eno1
Settings for eno1:
Supported ports: [ TP ]
Supported link modes...
I'm currently thinking about building a server for a proxmox installation.
This will provide a VM environment for a small company, with the following VMs (very basic details here, I know):
- 3x Win 2019 Server, 2Gb RAM, 1 vCPU, 40Gb disk;
- 1x Win 2019 Server, 4Gb RAM, 2 vCPU, 40Gb disk;
I was going to build a Proxmox server on a Supermicro 5028D-TN4T which utilizes the Intel Xeon D-1541 SoC chip.
However I am considering a AS-5019-FTN4 or a AS-E301-9D-8CN4. Both of these utilize the AMD Epyc 3251 Chipset. I know the AMD is Newer, but the Xeon D-1541 is tried and true. I'm just...
I'm hoping I can get some insightful input from this community. I'm looking at building out a new Proxmox cluster with Ceph as the backend. I'd like to get a couple of answers to see if this makes sense and if not where I should make changes.
Its a 2U 4 Node...
I recently tried to install Proxmox VE 5.3 on an older SuperMicro Node:
SuperMicro H8SGL-F Motherboard with integrated Matrox G200E Graphics
AMD Opteron 6348
128GB DDR3 ECC Ram
The Problem: Proxmox wouldn't boot, neither the installer nor a finished install from another node (Blackscreen...
ich teste gerade eine Konfiguration mit Proxmox VE 5.3-8
und habe ein Problen mit zwei NVME SSDs.
Die Grundinstallation hängt an zwei SATA SSD Platten auf denen ich zuerst die virtuellen Maschinen getestet habe. Hierbei gibt es auch keine Probleme - jetzt wollte ich noch zwei...
So we got a fancy new supermicro server were trying to install proxmox on now.
The installation went pretty smooth. However, I can't get either of the onboard NICs to work. The supermicro docs list them as an Intel C621 platform .
Proxmox / Debian recognizes them as Intel X722...
welche Hardware Voraussetzungen benötigt ein Supermicro Motherboard um unter Proxmox eine OPNsense Firewall zu virtualisieren mit NIC Passthrough (also WAN/LAN)
Würde unten stehendes funktionieren?
I have installed Proxmox 5.1 (latest release) on my Supermicro server with an X10 board last week.
Every 1-2 hours the server freezes and becomes unresponsive. Even typing in the IPMI KVM console doesn't work. Only when I do a hard hardware reset, the server reboots and boots proxmox...
I am attempting to install Proxmox (Ver. 5.1-3) on a system with two SSD units in a mirrored ZFS array. However, the system does not boot into Proxmox, and instead, dumps me into an EFI shell. Any assistance is appreciated.
My motherboard is a Supermicro A2SDi-8C+-HLN4F (BIOS Rev. 1.0b)...
Supermicro SuperDoctor® 5 | Supermicro Server Management Utilities | Products - Super Micro Computer, Inc.
Trying to install SD5 in a Proxmox build.
The installer goes through with no errors but it never gets installed.
In the past, I've installed SD5 many times on my XenServer hosts, all...
We are fighting to install PVE 4.2 on a brand new Supermicro with HBA and 5 SAS disks installed on It.
Configuration is quite straightforward and all disks are seen at install time.
First goal was to configure PVE on 4 disks in RAID 10 ZFS : I selected the four target disks and...