solved

Hi all, I'm passing the hard disk controller to the VM, after following the relevant documentation and setting up passthrough, I try to start the VM but I get the following error message: kvm: -device vfio-pci,host=0000:03:00.0,id=hostpci0,bus=ich9-pcie-port-1,addr=0x0: vfio 0000:03:00.0: failed...

At the moment HELO/EHLO check can be enabled or disabled... Nice... so far. Unless one has very simple equipment that cannot be configured to specify the HELO content (PLC's...), yep some are in the wild sending to the external interface. It would be nice if HELO check could be...

Hi, I have a physical host spun up with Proxmox 8.0.4 and running with a guest VM containing OpnSense. At the moment I am in testing mode so things are being setup on an existing network with separate router. Eventually I will retire the old router and replace it with my standalone box run so...

something strange is happening and i have tried multiple network interfaces file configurations with reboots I can Access my VMs/Containers via IP Address, but when i try to access the proxmox host via ping/web console/ssh all fail Server goes through 1 unmanaged switch to get to the firewall...

I was following this guide and ran into some trouble: https://pve.proxmox.com/wiki/Upgrade_from_7_to_8 I had set up all my repos to point to the new bookworm repos, and when I run "apt full-upgrade" the results are: root@home:~# apt full-upgrade Reading package lists... Done Building...

Hello, it's time to migrate :) but i've that warn from pve5to6: = CHECKING CLUSTER HEALTH/SETTINGS = PASS: systemd unit 'pve-cluster.service' is in state 'active' PASS: systemd unit 'corosync.service' is in state 'active' PASS: Cluster Filesystem is quorate. Analzying quorum settings and...

Hello, after upgrading Ceph packages from version 17.2.5 to 17.2.6, the syslog contains following warnings: Jun 05 09:20:24 pve01 ceph-crash[1883176]: WARNING:ceph-crash:post /var/lib/ceph/crash/2023-06-01T19:33:42.133764Z_6d5e3451-8d05-4932-8b5a-a86dca582440 as client.crash.pve01 failed...

I have hyper converged PVE cluster of 3 nodes using a ceph shared disk. Also i have a large disk for one of the VM/CT's that should be in iscsi storage. (where i have a few TB spare). (it fills 50% of the ceph storage and will grow ...). How to ensure the iscsi disk follows the Container, ie...

Greetings, I use Sennheiser PC-8 headphones. No problem with the sound on VM, unlike with the microphone USB devices as well as audio device added to VM hardware Ubuntu 22.04 is installed on VM Here is the outcome of aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA...

Hi All. I have searched and googled, I would like to know what the deduplication factor shown on the summary means. My deduplication factor on a data store is currently 10.77 I have no idea if that's good or bad. And does that mean 10.77% of data is deduplicated? If someone could please maybe...

Hi, I have searched the forum, but nobody seems to have faced this problem. I have a small cluster with 2 nodes, on each node, VMs are on a zfs pool and replication is active. Everything works fine, live migration is fast except for VM 500, on which snapshots were made through the GUI and later...

Hi there, after trying to clone my ssd (before upgrading to pve 7) I cannot reach my WebGUI anymore. My VM (nextcloud/pihole) are not running. I'm not shure if they still exist. I still can reach my node via ssh and I tried several solutions from similar problems, but nothing helped so far. I...

Hi, I upgraded our cluster to 7.2.4 (comming from last 7.1) lately, the /var/log/messages was filling up with kernel crash reports : May 19 17:00:05 pve01 kernel: [16498.218023] <TASK> May 19 17:00:05 pve01 kernel: [16498.266312] kthread+0x127/0x150 May 19 17:00:05 pve01 kernel...

it got code 43 in Device Management. in some tutorials, they say it would be fine, after installing the gpu driver. but when i installing AMD driver, it got Error 184

Hey , not sure if this is right forum to ask or not but am unable to see usb device in guest but only when trying using a cloud image based template. I've attached some screengrabs showing output but in summary Device is visible on host at /dev/serial/by-id/<device-identifier> If I attach usb...

Hello How to run NOW verification from commandline but only selected group backup from one datastore (or i future in GUI)? I have a tens of VM, with two VM very big (3TB) with very small files (eg 10-50kB) - need to run 2 verification line (at the same time): first: all VM's verification (with...

Hi all, today i restarted one node of our proxmox cluster with pve 7.1-10. This node now has a empty /etc/pve directory. I dont see any reason for that. So my questions are: 1. Is it possible to debug / find the issue for that? 2. There is / was a VM with ID 100 with local storage on this...

***LVM was full. I missed that. I am creating a new Ubuntu container, doing a release upgrade on it and then rebooting. After I reboot the container, it fails to start and gives the error in the title. I have deleted the container and tried again. I tried privielged and unprivileged. Both...

I have a 2 node cluster that I originally setup with a 1G network (192.168.15) and I've added 10G cards to the servers. I've migrated the back-end NFS storage over to the 10G network (192.68.10) and that seems to be working well. However, I think there is still traffic (for instance live...

I had deleted a vm via the gui console ( vmid 104), however from the command line it still appears, and If I tryto add anew vm, there isn't enough disk. any ideas ? and yes I want to delete the vm 104. thank you root@pve:/# qm list VMID NAME STATUS MEM(MB)...