Hello, I'm trying out Proxmox and I've attached a test machine to an iSCSI NAS. There are 62 LUNs. When I go to add a drive to a test virtual machine I click on storage and the "loading" animation is displayed but after a short amount of time it disappears and the storage box is empty. I don't...
Hello Proxmox Community!
We've got a 6 node Proxmox cluster running the current version of proxmox 4.4. The disks of our VMs are located on one of our 2 multipathed iSCSI SANs. We got a new one this year and rebuilt our network with 10 GbE DAC Ethernet, a physically seperated 10 GbE LAN and...
Hello
I have 50 vps installed in 40 micro servers (microblade with atom C2750 and 8G of RAM), the microblade is connected to an QNAP ES1640DC-V2 (dual controller with 4 SSD cache and 12 SAS Near-line 6T) for storage VMs.
All servers have 2,5Gbs/ network interfaces and are connected to NAS with...
We are trying to build HA cluster with iSCSI storage over dedicated network interface.
Looks like disconnecting storage network (in any way - physical fault or misconfiguration) doent lead to any reaction from PVE HA.
For example, if node connection to iscsi storage failed, we got messages like...
Hello,
I am setting up Multipath on Proxmox 4.4 following an online guide.
I have got to a point where I have logged in to my iscsi session and confimed that my SAN's virtual disks have mounted.
I have created /etc/multipath.conf and entered the following:
defaults {...
I have used iSCSI targets with single LUNs previously without issue however I now have a taget with two LUNs yet I cannot see how to reference the LUNs individually.
I can connect to the iSCSI target in pve yet only see one LUN listed.
Hello
I'm reaching out to this community as I'm just starting out with Proxmox and could do with some advise.
Does anyone have any experience of using a Dell MD3600i SAN with a Proxmox cluster?
We are very early in the planning stage and we are trying to do the best possible setup with...
Got a 4.4 production cluster attached to a multipathed iSCSI SAN from a HP MSA1040, divided the MSA into two disk groups A&B, then created 5+1 xiSCSI LUNs per MSA disk group and mapped those to PVs in four volume groups on each hypervisor node like this:
vgXbck LUNs are mapped to nfs server...
I want to connect an existing iscsi lun to Proxmox. I added the iscsi target (successfully), but I couldn't access the data.
Does anybody know how can add an existing luns into proxmox? (am I missing someting?) and where for is the option "Use LUNs directly"?
So I'm looking for a solution where ProxMox does its backups over the network to a FreeNAS box.
Last week I had this running very well using NFS until Tuesday morning when FreeNAS went offline.
To me if the NAS goes offline the backup should quit and get over it, but it didnt do that.
Instead...
I believe I have done this before without a hitch. Other sources seem point to adding ISCSI LVM as well however, I am not able to add an LVM its asking me to select a Base Volume. What step did I forget to do?
I am about to configure a NAS that’s suppose to supply the storage for 3 virtualization servers. And I need some advise regarding which base-system to chose. The NAS has good processors, sufficiently RAM, good disks and 10G connections between the servers… So I am mostly looking for general...
i want to use my iscsi target as volumegroup using multipath
i configured multipath and "systemctl status multipath-tools" says "active (running)" but will not create the /dev/mapper/ devices
i "fixed" it by adding "systemctl restart open-iscsi.service" in the rc.local
how can i be sure that...
Hi,
I guess ZFS over iSCSI would be better than just use iSCSI share + LVM on top of the iSCSI share,
since it gives the benifit of easy snapshot and clone right?
So I have a new installation of FreeNAS to provide iSCSI.
Is it best to use a new zvol and device type extend
or a new dataset...
Hi All,
Proxmox 4.2-18
Proxmox is attached to a SAN, which has a large LVM presented, and is in use for some containers.
Co-worker created 20/30 new containers on local LVM (only 800GB) by accident, what is the correct way to move these to another storage? downtime is no issue as these...
Hello,
I'm currently using Citrix XenServer 6.5 and considering switching to ProxMox (testing it with another physical server).
I'm using a Synology NAS as the iSCSI server. XenServer created LVM over the raw iSCSI for the VM storage. I have cloned the iSCSI target/LUN on the Synology for the...
Hi, this is my first post on this forum, i work with proxmox on my servers from version 2.x and I think this software is very powerful. Actually I’ve 3 cluster with drbd (6 servers) and some stand alone installation for a total of 22 proxmox installed.
I'm planning to install a Proxmox cluster...
Hi
We are setting up a cluster of Proxmox ver 4.2 hosts using shared LVM Groups with Network Backing via 10GB ISCSI to a Dell MD3800i SAN.
Just looking at the following post for Proxmox ver 1 it mentions that we need to consider using CLVM...
Hi,
we have setup a 3-node proxmox cluster (4.1) and configured two storages for VMs - NFS to our FreeNAS and iSCSI to our FreeNAS. iSCSI was configured using Proxmox Web UI (https://pve.proxmox.com/wiki/Storage_Model#LVM_Groups_with_Network_Backing)
Both, NFS and iSCSI, use dedicated 10G...
Hello community.
(this is my first post :)).
I was working with ProxmoxVE from the 3.0 version. I always followed the guidelines, wikis and forums, and so I was able to solve problems without major complications.
Thus tasks such as updating, re-installing nodes, configuration of different types...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.