ethernet

Hello, I am trying to set up monitoring with Wireshark in a Proxmox LXC container running Rocky Linux 9. Some notes on my config are below: 1) I am using a Ubiquiti USW-Lite-16-PoE switch. 2) Physical port mapping on switch: My PC is plugged into port 1, Proxmox's onboard NIC is plugged into...

Russia: Здравствуйте, был сервер на Ubuntu, но мне надо было изолировать системы, но не суть Я скачал proxmox, установил, при установки не что не трогал, ip был такой какой и мне система мне дала, когда я подключал по ethernet проводу к роутеру и устанавливал, то все хорошо работало, а если...

Hi I have a Proxmox 8.3 installed dedicated server. I have created two VMs with ALmalinux 9 installed on them. I have set of 13 usable IPs on my dedicated server. I can use the first VM with different IPs but second VM doesnt work with any IP. Both VMs are identical in every way, as they both...

The tg3 driver included in the Proxmox VE kernel for Broadcom Tigon3 ethernet occasionally crashes out with: DMA Status error. Resetting chip. Usually the interface comes back after a few seconds. Sometimes it doesn't, and the system must be rebooted. This is the exact bug described in the...

I recently learned that you can't run proxmox through wifi and you have to use ethernet. The room in which I'm renting has no connection to ethernet and I don't have a way to connect directly to the router. Would it be possible to run the traffic of the server through my main PC and still...

Hello I've a DELL PowerEdge T440 updated with last firmware, bios, hd, network avaiable. I've a DELL Ethernet Quad Port Broadcom 5719. Installed Proxmox 8.2 at each reboot I've a idrac error: A fatal error was detected on a component at bus 1 device 0 function 0 1 2 3 . We did some...

Hi everyone, I've just installed Proxmox on an old laptop without any particular expectation or need, just to fiddle with it. My problem is that the Ethernet connection doesn't work. I searched a bit on this forum and apparently it's something that happens frequently, but I tried all the...

Hi, so I just got a mini pc for a server and it’s my first time trying to install proxmox. The installation went fine, but for some reason proxmox isn't connected to the internet. I currently have an ethernet cable plugged into my router but I am unable to access the ip address website I set...

I had opened up my proxmox GUI and my ethernet wasn't working on any of my VM or containers. I tried fixing it but I couldn't. I didn't change anything when it stopped working and I don't know how to fix it.

I've installed a PCIE NIC into my machine running Proxmox, but no new interfaces are showing up under the network tab. I can tell that the NIC is detected by the computer because it shows up when I run lspci | egrep -i --color 'network|ethernet', which I've shown in the first screenshot. The NIC...

Hallo, ich habe Proxmox aktuell auf einem Intel NUC laufen, allerdings ist die interne SSD nur 128 GB groß und wird bereits fast komplett ausgereizt. Deswegen möchte ich stattdessen eine SSD mit 256 GB, die ich noch herumliegen habe, benutzen. Dazu klone ich die 128-SSD mittels Clonezilla...

I am trying to add a 2.5" SSD to my system using the Accelsior S PCIe adapter card. When I add the card to the system and boot, I can see the disk drive in fdisk as well as format, add/remove partitions etc. But then my ethernet connection is broken: Jan 13 14:26:08 pve-1 networking[887]...

Hi everybody, I just installed Proxmox and tryed to ping www.google.com because the web interface didn't worked. It showed: "ping: www.google.com: Temporary failure in name resolution" I am sure that the Ethernet Ports work just fine and I don't know what to do about it. I let Proxmox run on a...

When running iperf3 between devices on my LAN I am having an issue with my network throughput. I have a Beelink EQ12 with Intel i225v chipest and when connected to a 10GbE switch via SFP+ tranceiver I am able to get 2.5GbE throughput on the upstream to iperf3 servers but when going downstream it...

Hey, a few days ago I updated my Proxmox host system via apt update and apt upgrade. Since I'm still using PVE 7.4, it tried upgrading the pve-kernel package from 7.4.7 to 7.4.8. However, after rebooting my server later on, it wasn't connected to my network anymore. My system uses a r8168...

I'm trying to get Proxmox up and running with this PC. It is a clone of the Minisforum GK41. This PC has two separate ethernet controllers, each wired up to one of two ethernet ports on the back of the machine. I have tried to plug an ethernet cable from either of these ports back to my router...

I added another ethernet to my server - I did it as in the presented tutorial: https://www.youtube.com/watch?v=XVcov48673Y Unfortunately after this I see that my new ethernet is not active. Any idea how to activate it?

Good Afternoon All, I have a Laptop that I wanted to test GPU passthrough on sitting in my closet for a year gathering dust. I turned it into a small proxmox node to host maybe one or two VM's to test GPU passthrough. However, this laptop does not have an ethernet port. It did however come with...

After giving up on PROXMOX on my B450, I've decided to try it on my Asus Tuf X570, but after install there is NO CONNECTION from PROXMOX. Just for testing purposes, I've decided to install Debian 11 (net installer and Plasma DE) to make sure if this is a Debian issue, but it works fine. Also...

I had one Intel X550-T2 installed on my server and all VMs were running fine and I setup OPNSense and had it configured with the two ports from the X550 being LAN and the onboard ethernet being the WAN interface using bridges. However, for OPNSense to really replace my router, I needed more...