proxmox 8

I created a new windows 10 VM for the game with a 2060 SUPER in EGPU (Connect in thunderbolt 3) in passthrough, I can update the card drivers, I was able to play minecraft for 20 min but now I have the vm that goes into "Internal error" on proxmox IOMMU groups : in an IOMMU group I have both...

I have just set up a three node cluster, extending my single host setup. pve1 = 172.x.x.10 pve2 = 172.x.x.20 pve3 = 172.x.x.30 Each node can ping the others fine. From pve2 and pve3 I can ssh to pve2 pve3 and pve1 fine. Nmap also shows all ports open. All nodes use a vlan ID of 5. My issue...

went from kernel 5.15 to 6.2 and now when ever my truenas vm tryed to load the nvme drive 0000:03:00.0 i now get vfio-pci and pcieport errors. the drive is on a pci bifurcation card. any help would be appreciated specs i5-11400 in a z490i aorus ultra 64gb ram the drive in question is an Intel...

Hello all, My Hardware: Motherboard - Asrock Rack Rome8d-2t CPU - Epyc 7F72 RAM - 128GB 3200MHZ ECC GPU - RTX-2080 Super - passed through to Windows OS Drive - Samsung 980 Pro 500GB VM OS Drives - ZFS Mirror 2x960GB Samsung P9A3 Windows VM Game Storage - ZFS Mirror 2x1TB WD SN850 HBA Card -...

Hi I'm currently researching in updating from PVE 7.4-17 to 8. I currently have the LSI MegaRAID 9341-4i Raid card installed and is detected and working in proxmox 7 as you can see from the pictures below : When I upgrade to Proxmox 8 should I be worried that my card will not be detected...

Hi, I could use some guidance. I am setting up a workstation with proxmox 8 and kde plasma (replacing Windows 10 + VMware). This system has a single Nvidia 3060 ti. After installing proxmox, I set up kde plasma and ram into an issue where the desktop environment was a black screen with my...

Hello everyone, I managed to install macOS Ventura on my fresh Proxmox 8 installation. Everything went fine, installing macOS through the noVNC console and setting up everything. Now its the last part to my success that does not work: the GPU passthrough. After the initial Proxmox booting...

After upgrading to PVE 8 and several CTs to Debian 12, I experience a loadavg discrepancy. The load averages shown in the CTs are that of the host, divided by the number of CPU cores of the LXC container (per-core loadavg in Zabbix), instead of the load of the LXC guest itself. The commands...

I'm not really looking for support here because I have everything working now with 8.0 and that's enough. I'm more writing as a 'bug report' of sorts. I have purchased a new box intended for use as a router/firewall/etc with Proxmox VE at the top level. i7-1265u, 64Gb DDR4-3200 RAM, 1Tb main...

Hello everyone, I have been thinking about fully encrypting my Proxmox 8 server which is located in an external data center. I would like to use Luks so that the encryption password is requested when booting which I can then enter via SSH. Now I have found the following instructions and have...

Hello In the middle of the night I had an impulsive thought to update my proxmox 7.2 to proxmox 8. First I updated tot 7.4 then I changed the repo file and I tried to apt dist-upgrade. It gave some error codes so I tried to reboot. After the reboot the system constantly gave a error with...

Hi Guys, I'm trying to install TrueNAS Scale VM on Proxmox 8.0 and in the process, I'm trying to pass-through 6 disk to the VM. I want to specify that my boot drive that proxmox is installed on are actually two mirrored NVMEs and it appears as ZFS in the system. 4 of the 6 disks are on a SATA...

Hallo Forum, ich wende mich nun mal an euch, da in einem von vier Fällen das Upgrade leider nicht geklappt hat. Ich habe ein einfaches NAS gebaut, welches Proxmox als Hauptsystem hat. Kurz zu den Specs, falls es wichtig wäre: - Intel i5 10500T - 40GB RAM - 128GB NVME SSD für das System - 3x...

Hello everyone. General description I wanted to reinstall Proxmox while keeping all my vms (My setup consists of a single server with a local storage. Simple raid, no external storage trough nfs...). I followed a guide from Guillaume Matheron Reinstall proxmox while keeping all the...

Moin I have problems with my Proxmox installation I have installed Proxmox on my Supermicro x10dri-t. I was able to let it run normally until I had to change the BIOS battery and stupidly turned off the server. After that, of course, everything was adjusted and the former raid 1 was destroyed...

Hello forumers, I am working on the migration from old Proxmox 3 VE to the newest version. As I know one of the simplest ways to move KVM from old environment is using backup and restore options: In case of containers it should be converted from OpenVZ to LXC because OpenVZ isn't available...

Hello everyone, After my first installation of promox I have this Warning: "nvme 0000:01:00.0: AER: Error of this Agent is reported first" My computer Model: HP Z640 Processor: Intel Xeon 1640 V4 RAM: 4*16GB DDR4 2400 MHz ECC NVME: PCIe Samsung MZVKW512HMJP-000H1-HP I have 2 other computers...

Dear Proxmoy-Experts, Since some days now, the performance of every machine and container in my cluster is extremely slow. Here some general Info of my setup I am running a 3 node proxmox-cluster with up-to-date packages. All three cluster nodes are almost identical in heir hardware specs...

I was unable to see any of the 4 ethernet ports I have (eno1-4) using `ip link show` after upgrading to Proxmox 8. When choosing to boot from the earlier kernel, it immediately shows up. Is my NIC no longer supported? Included in this category because it is a kernel-level issue. Thank y'all...

Hi! There is a Netflow/IPFIX package for iptables in the base Debian12, but not compatible with the pve8 kernel 6.x Is there any way to make it to work? https://bugs.launchpad.net/ubuntu/+source/iptables-netflow/+bug/2023306 $> aptitude search netflow p iptables-netflow-dkms...