network interface

I am new to proxmox as of a few weeks ago, and am trying to replace VMware because I'd rather avoid paying VCenter pricing to save the department money. So all advice is welcome during their trial period. On our servers, we have dual NIC cards, after some time, I was able to get a continuous...

I upgraded a server from proxmox v3 to v5 via reformatting. Then I added in the network interface file the same IP config from v3. I am able to access proxmox interface however the additional IP ranges that were on the host interface are no longer working for the containers. I have read the...

After updating to latest systemd* packages: libsystemd0:amd64 (232-25+deb9u9, 232-25+deb9u11), udev:amd64 (232-25+deb9u9, 232-25+deb9u11), libudev1:amd64 (232-25+deb9u9, 232-25+deb9u11), systemd-sysv:amd64 (232-25+deb9u9, 232-25+deb9u11), libpam-systemd:amd64 (232-25+deb9u9, 232-25+deb9u11)...

Hi, I have a box with 8 built-in NICs on the motherboard which I'd like to be used as a firewal and switch for my network. I have pfSense and Ubuntu Server installed inside of the Proxmox. I'm struggling to configure pfSense/Proxmox in such a way that pfSense (or/and Proxmox) will be used as a...

Hello I currently have a dedicated server on hetzner with 2 extra ips. So in total I have the default ip that is included with the server (xxx.xxx.61.76) and the other 2 are (xxx.xxx.61.116 and xxx.xxx.61.117). With only the default ip I had my vms "natted" with internal subnet to that public...

Dear all, I've been struggling with setting up my server for a few days now. Here is my situation: I have a server with one network interface. I have a public IP x.x.x.3 and i ordered another public ip wich is x.x.x.21 What I'm trying to do is to setup two subnets, one for each public IP. I've...

Hello So i installed Proxmox on my server. I configured a Bridge and NAT interface for my VM's. I installed my first VM (Ubuntu) configured the port forwarding and tried to connect to it with putty -> Connection time out. I double checked everything twice, firewall, ip configs, ports, but i...

Hi everyone Since the startup of the server, there is a problem with network server failure. Network server is disconnected and re-connected every so often. message log: Jul 11 06:40:15 isvps085 kernel: [60086.694591] vmbr0: port 1(enp0s31f6) entered blocking state Jul 11 06:40:15 isvps085...

Hi, For some reasons I have 2 bond interfaces: bond0 4x1G for public network with PVE with OpenVSwitch. bond1 2x10G for Ceph. Note: this network is absolutely isolated on dedicated switches with no uplink. By default migration was done on the public network instead of the Ceph. Having the...

Hi, Do you have a solution for remote access to virtual machines with only one public address for proxmox server and machines connected with NAT configuration? Regards Thank you

Hello, i'm facing this problem on my server running proxmox, the server goes down often and if i go to /var/log/dmesg of my lxc container i see this: [96778.325439] IPv6: ADDRCONF(NETDEV_UP): veth102i0: link is not ready [96778.595101] fwbr102i0: port 1(fwln102i0) entered disabled state...

Good day, It appears that pvestatd doesn't track all the traffic on all the interfaces in the host summary page, only the "primary" interface. Any pointers how to tell it to track all/other interfaces too?