Hi all,
The default network config works fine with a Vultr VPS and NAT:
iface ens3 inet manual
auto vmbr0
iface vmbr0 inet static
address 202.111.81.143/23
gateway 202.111.80.1
bridge-ports ens3
bridge-stp off
bridge-fd 0
auto vmbr1
iface vmbr1 inet static
address...
I get that Proxmox is setup for enterprise but it works great for a home lab. Where slower drives are common...
3.2 all default settings with sata 7200 drives
Old desktop pc - FSYNCS of around 1200
I/O is ok
4.3 all default settings with sata 7200 drives
VMware on Windows PC - FSYNCS around...
Hi all! I installed the latest Proxmox 3 on a vmware VPS hosting service – they installed from ISO as I don’t have full console access. It works perfectly but I can’t figure out the network model I should be using and wish to secure both the host and containers.
As per the wiki network model...
Hi all,
My Proxmox 1.9 drive failed so I have rebuilt it and added the second storage drive from the gui.
Is there a method to 'recreate' the VM's from this storage drive?
I have seen this command but I'm not sure how the --ide0 should be set
qm set 106 --ide0 /dev/SataDisk/vm-106-disk-1...
Proxmox installed on my hosting service shows this default etc/network/interface file
# network interface settings
auto lo
iface lo inet loopback
iface eth0 inet manual
auto vmbr0
iface vmbr0 inet static
address 115.55.23.5
netmask 255.255.252.0
gateway 115.55.23.254...
Hi all,
I am Currently running a Ubuntu 8 container and I need to log the Boot/Init output that can be seen in Proxmox. I have tried syslog and boot log in Ubuntu but neither show this output, anyone know how to do this?
I was running 1.5 with NO changes at all, then I rebooted it and noticed the openvz container timezone was off and running SLOW. I checked the host and found while the timezone was correct the time was wrong... I have upgraded to the latestest kernal and proxmox 1.9 and no change.
I have run...
There is nowhere in the gui to set details for an smtp outgoing server to send mail for backups etc.
It seems like its not really supported. How is this setup?
Running VE 1.5 on an Intel Quad core, After a reboot the server time is correct, then it slowly slows down, something like 45 minutes slower over a week. A reboot fix's it.
I noticed these kernal errors also(maybe to do with vzdump),
kjournald starting. Commit interval 5 seconds
EXT3 FS on...
Hi all, I've had a good look around but can't find a definitive method to extend the local partition, for some reason this was the size when it was made.
I have read through some of the guides but its over my head and dosnt seem that specific. Can anyone point me in the right direction...
Hi all, how do I point too and restore my NFS VMdump backups?
The wiki states this format: vzrestore vzdump-openvz-777.tar 600
But how do I point to the nfs share?
I just installed an NFS server and have pointed to it for backup, when the NFS server is off I'm getting the below server error. I turn it back on and everything works, why would it cause this when the nfs backup I created only needs the server at a specific time?
Internal Server Error
The...
Under storage it shows Used 7.35GB and Capacity 9.35, 9.35 was the default size plus 3 containers. When I migrated and backed up at one point this read Used 9.35.
How and should this be expanded?
I'm running Proxmox in vmware and made the HDD 20gb so I figure 9.35 is some sort of default.
Somehow or other a ubuntu container will not start, when I restart it it's status just returns to mounted. Something may have happened when I was doing a migration between nodes.
I'm a novice but I entered 'qm reseume 102' and it said unable to read config
The log just states that it has...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.