I have been trying to connect my container running the Ubuntu 18.04 template to my network (and by extension the internet), however, I cannot configure netplan to send data.
I'm trying to create a container based on the Ubuntu Minimal, available here. The disk seems to be created successfully, but then it fails on the network interface. I have tried both Bionic and Focal. Here is the output:
Logical volume "vm-105-disk-0" created.
mke2fs 1.44.5 (15-Dec-2018)...
Forgot to set default gateway in container settings. It didn't carry over from vmbridge.
I'm new to this forum and PVE, sorry if this is in the wrong place. I noticed the problem when trying to download java from default repo and it wasn't connecting to archive.ubuntu.com and I also...
I am attempting to install Ubuntu 20.04 (though I am encountering the same issue on Ubuntu 18.04) on Proxmox 6.2-4, however the installation usually fails partway, and on rare occasions when it does complete the VM hangs on "Booting from Hard Disk"
I've tried peoples'...
Having Kodi up and running on my Proxmox server (HDMI output, HDMI sound, and hardware acceleration). Need to be able to passthrough GPU & Audio. The target would be to have it running on Debian 10 (best would be Libreelec but i was not able to make it run; i've stopped my...
I have an additional IP on my Hetzner server with Proxmox that I want to route it to an Ubuntu guest machine
Here is my network configuration on Host and Guest machine
My guest machine is Ubuntu 18.04
And configurations don't work
My PVE Host net config:
# network interface settings...
I have managed to set Proxox 6.0-4 up in a virtualbox vm and have created an Ubuntu 18.04 container with which I will run Plex media server. I have also managed to get Proxmox to see my Synology NFS share (see screenshot) but I have spent 2 days attempting to attach the NFS share to the...
I have a ubuntu lxc - container with ubuntu 18.04 and installed snapd, but with problems. In my lxc config I have the following lines added:
I can start the snapd container with rocketchat server but in syslog I have the...
New to Proxmox , I recently installed on a OVH's dedicated server a 5.4-13 (zfs) Proxmox VE.
I needed to have one LXC container with 1 unused public IP (IP failover) and 1 LAN IP (for connecting with other LAN-only containers).
I used the set up described by OVH (ovh mac address , fail-over IP...
I had an ubuntu 18.04 working and decided to move it to a VM in Proxmmox.
Configuration includes a bridge, it was working fine in the previous system but it does not come up at boot in the Proxmox VM.
Here is my netplan config:
We are migrating container from Ubuntu 14 to Ubuntu 18.
We have a configuration with routing inside the container (in /etc/network/interfaces) :
iface lo inet loopback
iface eth0 inet static
I have tried to install Ubuntu 18.04 LTS Server in a KVM machine on a recently updated Proxmox 5.4 host, but after entering the IPv4 address manually, and hitting "Save" the installer instantly restarts. Tried different hardware configurations (E1000 vs. VirtIO-net, disconnecting the adapter...
It's been 5 days that I try to install Ubuntu 18.04.2 and it always fails; The installation itself goes well but when I remove the installation drive (iso image) and reboot it, the VM remains stuck at the boot from "HD drive" or at the " grub rescue";
I tried changing the...
Hey everyone, this is my first go at setting up Proxmox. I have an Ubuntu 18.04 VM running on an older HP Z400 with an upgraded AMD FirePro v4800 GPU. I setup the GPU passthrough as described by the docs and lots of googling. I was able to get Ubuntu to see the GPU but performance is awful, it...
Hello, I've been using px 5.0 for some time, now I've installed 5.4 in a new server (OVH) and having some weird network issues using LXC containers.
I have a LXC container (ubuntu 18.04) with a public IP (eth0 to vmbr0, mac = virtual mac created on ovh panel, gw = host ip but ended on 254 as...
Hello Proxmox Community,
So I recently I installed Proxmox VE 5.3 on my Dell PowerEdge R710. Set up the interfaces for my DHCP network and its been working great so far ... well, except one issue.
I'm currently attempting to create a Discourse Forumin an Ubuntu Server 18.04.2 LTS VM. I set the...
I have a ubuntu 18.04 guest running in a KVM due to kernal modifcations for a WireGuard server to run on it. When preforming a speedtest with speedtest-cli, I get the following output:
Testing download speed...
Download: 73.61 Mbit/s
Testing upload speed...
Upload: 3.60 Mbit/s
yesterday, I wanted to try out the latest Ubuntu LTS version 18.04.2 and installed it as a normal VM on my PVE-Server (v.5.3.9). Unfortunately, it wount start after installation has completed. After removing the ISO from the drive the startup is stuck in the fsch dialog as displayed in the...
Hi, I have a Proxmox server with several VMs.
This problem has happened twice now, I have a VM with Windows 10, another with Ubuntu 18.04 server with NextCloud 15. I had to copy some files and that easier than connecting to the cloud of my NextCloud, and the surprise was that the network is...
I have problems after I upgraded my LXC Container from Ubuntu 16.04 to Ubuntu 18.04 with do-relase-upgrade:
Failed to attach 321 to compat systemd cgroup /system.slice/nginx.service: No such file or directory
Any idea what I can do now? I have the problems with some service like ssh...