ixgbe

I am having problems with a driver situation on my Proxmox 8. I have a machine with 1 onboard network card and 2 offboard network cards (1 ethernet and the other fiber). As it seems to me at the moment, the onboard uses tg3, the ethernet uses igb driver but the fiber uses ixgbe, for some reason...

I'm trying to use a network card on my server, I've tried some configurations but without success, would anyone have any guidance on this? -network card does not appear in IP link Proxmox: 7.4-3 I tried this and it didn't work: $modprobe -r ixgbe $modprobe ixgbe allow_unsupported_sft=1 $...

Hi, I am having some trouble getting a newly installed Supermicro AOC-STG-i2T 10-Gigabit NIC up and working . I have tried quite a few solutions suggested on this forum and elsewhere to activate this network card, but none of them have worked. Can somebody please help resolve this issue? Here...

Hello, I have two supermicro servers (SM-HV01 and SM-HV02) running proxmox ve 7.3-4. These servers are directly connectet with two 10Gbit/s Fiber DAC Cables (enp3s0f0 and enp3s0f1), and one 10Gbit/s Ethernet cable (eno2). The outside interface of these two servers are connected to the...

Hallo Ich habe das Problem nach dem Update ixgbe 0000:06:00.1: Warning firmware error detected FWSM: 0x00108013 ixgbe 0000:06:00.0: Warning firmware error detected FWSM: 0x00108013 ixgbe 0000:06:00.1: Warning firmware error detected FWSM: 0x00108013 ixgbe 0000:06:00.0: Warning firmware error...

Hi all, I have 3 boxes, 2x Proxmox 6.3-6 (1x Xeon E3-1220V2 1x FX 8350) latest intel ixgbe driver and 1x Unraid 6.9.1 built in ixgbe driver (1x Xeon E3-1220V2) all of which seem to have the same issue with the 2nd port being detected, the link state being detected and negotiated to 10GBase...

I've replaced a 10GbE adapter in one of our Proxmox nodes that was running a bonded pair of Cat6 cables to an aggregate switch. The old NIC and its replacement are both Intel Ethernet Controllers (10-Gigabit X540-AT2) so I assumed (probably incorrectly) that all I'd need to do was plug it in...

Hello everyone. I'm new on proxmox. So please forgive me if any mistake i made. I have deploy a new proxmox 5.3 installation. I use QuantaGrid D52BQ-2U server which include 2 Ethernet and 2 SFP+ ( Intel® Ethernet Converged Network Adapter X520-SR2 ) module on PCI card. When i have done proxmox...

I am running Proxmox VE but whenever I insert an SFP+ in my intel 10G card it disables the network interface. This is what I am getting after boot from DMESG: ============================== root@proxmox:~# dmesg | grep ixgbe [ 1.095868] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver -...

hi, i have 3 identical servers with integrated dual 10g sfp+ eth and dual 1g eth [Supermicro X10SDV-2C-TP8F] - the 1g nics are connected to redundant switches (frontend) - the 10g nics are connected direct (backend ceph) I tryed the configuration, shown in the video, but after restarting the...

I have four ports that is trying to use ixgbe driver to load. But when trying to initalize the ports, I get an error message in dmesg. I'm using kernel 4.13.13-6-pve. I'm currently using the ixgbe driver shipped with the installation (5.3.3). But I've also tested latest version aswell, with same...

I want replace Esxi with Proxmox, but where is some problem with network. After 12 - 15 hours linux bridge vmbrX wich connected to Windows 7 guest is freeze. After each port failure host reboot improve this issue. Output of /var/log/messages is attach. I googled problem but recommendation isn't...

Hi all. New to this forum and Proxmox, so please bear with me :) I just installed Proxmox VE 5 on a Supermicro X10SDV-6C-TLN4F board. The 1 gbit NICs where recognized right away but not the 10 gbit ones. I've been looking a little bit around and from what I've been able to tell, I need to...

Hi all, Finally support for Intel X550 has entered testing phase in Illumos (Omnios) ixgbe driver:-) http://elemental.org/webrevs/x550-final/