Search results

I am adding my issue to this thread. I ran through all these but should have checked journalctl first. The port showed good using ss. I then checked journalctl and found system could not read /var/log/pveproxy/access.log. Checking permissions it was set to -rw root root . Looking at my other...

I did the vcpu and it works like a charm.

Thanks for the pointer. I am going to try it out.. I was able to pass the GPU and a VF nic through to Ubuntu. Windows 11 wasn't happy with either.

Thanks for the pointers. The kernel parameters were from my notes when I first did pci passthrough on VE 5 or 6. I made all the changes you recommended and now the audio is correct, 02:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1) ... Kernel driver in...

I picked up a Supermicro X9SRL-F installed Proxmox VE (pve-manager/8.3.1/fb48e850ef9dde27 (running kernel: 6.8.12-4-pve) and I am trying to get PCI passthrough to work on a NVIDIA Corporation GP106GL [Quadro P2200]. While the Video is getting set properly "Kernel driver in use: vfio-pci" the...

I am running: root@pveprod:~# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 12 (bookworm) Release: 12 Codename: bookworm Linux pveprod 6.8.4-2-pve #1 SMP PREEMPT_DYNAMIC PMX 6.8.4-2 (2024-04-10T17:36Z) x86_64 GNU/Linux grub...

I had an Intel i350 setup with SR-IOV and it was working fine. I could use ViFs with Linux, and Windows 11. I swapped out the i350 with an i710. This was smooth as the OS saw the new NIC and it seemed to work. I changed the # of Vifs from 7 for the i350 to 32 for the i710. I have assigned ViFs...

That was it, thanks dir: vm_images path /tank/vm_images/ content images prune-backups keep-all=1 shared 1 changed to dir: vm_images path /tank/vm_images/ content rootdir,images prune-backups keep-all=1 shared 1

On my test system I ran PVE7to8 and got this warning on my only LXC vm WARN: CT 102 - volume 'vm_images:102/vm-102-disk-1.raw' (in config) - storage does not have content type 'rootdir' configured. WARN: Proxmox VE enforces stricter content type checks since 7.0. The guests above might not...

while the doc is not 100% clear, your pointers got me over the hump. Mirror is back together and system boots just fine. Thanks ! root@pveprod:~# zpool status rpool pool: rpool state: ONLINE scan: resilvered 7.34G in 01:23:32 with 0 errors on Wed Nov 1 20:09:15 2023 config: NAME...

Got it. Thanks..

It looks to me the guide you posted was to replace a rpool device and not to recreate a rpool mirror. Am I mis-reading this?

I had a bad disk in my rpool. I replaced the disk but the new disk turned out to be really slow. I decided to remove it with zpool detatch . I am trying to attach a new drive to the rpool but I get an error. See below root@pveprod:~# zpool status rpool pool: rpool state: ONLINE scan...

I am getting flooded with: IPv4: martian destination 0.0.0.0 from 192.168.1.1, dev ens2f1v0 I am using SR-IOV on a an intel quad port i350 nic. ens2f1v0 is a passthrough to an LXC container. This nic is 5:10.1 root@pveprod:/etc/pve/lxc# ip -br a lo UNKNOWN 127.0.0.1/8...

Thomas, I followed the directions and like you had an issue getting the container to be seen. I have a zpool setup for container templates since I use a 64G USB key for Proxmox OS. I made sure all file types were selected under Datacenter->Storage->templates. Templates points to zpool...

The edit worked. All set thanks again..

Thx for the clarification. The bios is at its latest level. The system is an lga2011, manufacture will not be doing any more update AFAIK. Will make the change and try again.

I had a disk in a ZFS mirrored rpool go bad. I put the new disk in (USB Key), did: sgdisk <good_rpool_disk> -R <new_rpool_disk> sgdisk -G <new_rpool_disk_> zpool replace rpool <bad_disk> <new_rpool_disk-3> proxmox-boot-tool format <new_rpool_disk-2> proxmox-boot-tool init <new_rpool_disk-2>...

This turned out to be a disk HW issue. One of my CACHE disks was bad causing zpool issues. Replaced the CACHE disk and things are running like a champ. found this by running zpool iostat -v zones 3

I have a couple of Windows 10 VMs and all of a sudden disk Active time goes to 100% and with very little disk transfers. I have tried different virtio settings and nothing changes. I did a forum search and found someone else had the same issue but no resolution. Any ideas? Let me know if you...