Search results

Sorry about the cross-post, but I posted a question about NAT-ing LAN to WAN addresses in the Networking forum. If anyone can help I'd be very grateful: http://forum.proxmox.com/threads/21122-How-to-NAT-LAN-to-WAN

Hi parlitul - were you able to resolve this? I think I've got the same problem as you had. So far, I've found no solution. Is it not possible to NAT using Proxmox? http://forum.proxmox.com/threads/21122-How-to-NAT-LAN-to-WAN

Remove these lines from the KVM guest's config: bridge_ports vmbr0 bridge_stp off bridge_fd 0 so that it looks like this: auto eth1 iface eth1 inet static address 10.10.1.9 netmask 255.255.255.0 (That works for me at least - now I just need to work out how to get the private...

UPDATE: As a result of the research on this thread, it looks like like you cannot use private IPs behind your Proxmox host's true IP, and masquerade the traffic using NAT, as stated here Using Proxmox 3.4, I've given my (Linux) guest both public and private network addresses. How can I get...

Re: grub2 update problems (GUI only), leading to not correctly installed packages Hi - just a suggestion: when you say "do NOT use the GUI for upgrading" it would be clearer to say "Upgrade over SSH, do NOT use your web browser for upgrading." This is because I read the above warning, and...

Ah OK - seems simple enough. Thanks!

Thanks, that's exactly my configuration - fingers crossed it will all come up and be OK. Indeed - I'd like to work out a safer way of doing this, but I'm not entirely sure how to go about it in the limited time I have to install the machine. Do you know of any HOWTOs on this? For example...

I have a default install of Proxmox 3.3. I have told my ISP that intend to virtualize my hardware, and asked them if they are OK with having multiple MAC addresses on the same NIC. They say they are OK with that. I am currently using 5 public IPV4 addresses on a phyiscal machine which I intend...

I used clonezilla-live-2.3.1-18-i686-pae.iso Maybe it wasn't the virtio then. It seemed to work (over an SSH share) after I tried it with SATA instead, but maybe that wasn't relevant. I still can't get the disk image to load from a USB drive attached to the VM though. Clonezilla either won't...

Well, it may have been virtio, but it's hard to say. Thanks for the tip about fsarchiver - I'll have a look. There's something deeply confusing about the way clonezilla works...

OK so it looks like the VM needs to have a bus type of IDE and not VIRTIO as I was creating it.

Odd that eth0 is missing. As far as I know I'd not altered anything other than the address line. Anyway, now I know I can do it via the GUI, so that's OK.

I'm following the instructions here for using Clonezilla to do a P2V: http://pve.proxmox.com/wiki/Migration_of_servers_to_Proxmox_VE#Physical_server_to_Proxmox_VE_.28KVM.29_using_Clonezilla_Live_CDs I've made a disk image (stored over SSH to a remote machine) from my physical machine. But when...

It's the default - I simply want to change the IP a a test - it's on the same subnet for the moment: auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet staticaddress 192.168.1.203 netmask 255.255.255.0 gateway 192.168.1.1 bridge_ports eth0 bridge_stp off bridge_fd 0 Oh...

I'm installing a Proxmox 3.3 host machine which will later go onto another network. So, I need to be able to change its IP address. I thought I could just put the new network config into /etc/network/interfaces. However, when I reboot, I can't get through to the management interface on the new...