Recent content by norsemangrey

Hi guys. I'm in a bit of a squeeze. I have set up three small machines running Proxmox (8.3 / 8.4) in a cluster. Mostly just to be able to move VMs between them if required. The one running 8.3 is out of the picture as the two others has been moved to a new location for a demo. No issue really...

Anyone else has any tips on this?

Thanks for the tip, but the link in the thread does not seem to work.

I am using HAProxy on pfSense to access my PVE cluster as I am accessing PVE from a different VLAN. However, when accessing PVE via the reverse proxy, using the Console for PVE itself or any VM is working only sporadically, and times out most of the time. The HAProxy configuration is very...

Thanks. That worked just fine. Learned something new today :) Now to something more tricky perhaps. The bottom interface is a (vmbr4) is a trunked interface / VLAN aware (I have just started configuring VLANs on pfSense). Should I be able to do the same thing there? I guess, perhaps not...

Sorry if my terminology is off. Hopefully you will get my meaning. My Proxmox host has 5 NICs. My router is a virtual pfSense running on Proxmox providing two subnets (SEC / IOT) connected to separate physical switches from the Proxmox NICs. The console interface to Proxmox is now on a...

This is a good point. I would like for the VM to only listed for packets on the selected VLAN. I am using untagged VLAN / VLAN 1 as a management VLAN which an application on the VM should have access to. Not sure what you mean exactly when you say that the switch needs to allow tagged VLAN 1. My...

I managed to solve it. I had to go into the network configuration on the guest OS and add the new interface (ens19) for dynamic address assignment. I would have thought this would happened automatically when a new interface is added. /etc/netplan/00-installer-config.yaml network: ethernets...

If i try to up the link the link status goes to UP (I do not see any error message), but it still does not get any IP. sudo ip link set dev ens19 up I have not done anything with the Guest OS network config in particular. It is an Ubuntu Server image on which I have installed UFW and Docker...

I have an Ubuntu VM for which I want two interfaces: one interface for untagged traffic (i.e. VLAN 1) and one for a specific VLAN. I am not quite sure about the correct way to configure this in Proxmox. I have a VLAN aware bridge where a VLANs are trunked (vmbr4) and if I create a VM with a...

Sorry for awakening an old thread, but I am struggling with the same thing. If I want the UI to only be accessible on a specific vlan (is this advisable?), how would you prevent Proxmox from listening to all ports. Also, how is the vlan device (vmbr0.10) tied to vmbr0? Is Proxmox just looking...

Ok. I just do not see from your example how they (th Linux VLANs you have created) are tied to the bridge you have for your physical ports (other than the name, vmbr1.xxx). I did some experimenting today where I hooked up a Unifi switch connected to a Unifi AP to a spare port in the Proxmox...

@rason @striker54 thank you very mutch for the input! I have a couple more questions though. The VLAN intefaces I create in Proxmox, are they only for "internal" use (i.e. for the VMs / CTs running on Proxmox) or are they required also for the physical interface(s). So I would do this by...

I am quite new to vLANs so please forgive me of my terminology is off. Today I have pfSense running as a VM on Proxmox (on a computer with 5 NICs), which is working great and up until now I have only been using subnets as I have not had any vLAN aware equipment. However, I have now bought some...

I'm running a small Proxmox server at home just to virtualize my pfSense router/firewall and a Home Assistant OS. The server has a NIC for WAN, LAN and one for the PVE console. I fairly new to using PVE. Is it necessary for me to enable the firewall/add rules at any level in Proxmox? I'm...