Latest activity
-
JohnnieKF replied to the thread May I ask if PVE supports the following operating systems.PVE doesn't have a 'supported' list, I am assuming this is a list of VMs you're wanting to export from an existing system like vSphere? You can run essentially any x86-64 OS, so all of those are fine. The OS Type field in PVE isn't a... -
Zzash1958 replied to the thread Second IP address on vmbr0.Both are in different subnets/networks. First, existing on 192.168. The second should be in a 10.x network
-
Llonger replied to the thread Second IP address on vmbr0.As mentioned in the thread above: "For two IPs in two subnets, you will need a second NIC." However, if your node is standalone (not part of a cluster), you can easily add two IPs from different subnets on the same bridge using a command like...
-
Ppoulpor replied to the thread Opt-in Linux 7.0 Kernel for Proxmox VE 9 available.I'm experiencing exactly the same issue. With 32 GB of RAM, I have to leave 8 to 10% free, or the Proxmox host freezes and the fans go wild. I first noticed this after rebooting following the update to kernel 7.0: the fans went wild, and I...
-
Moin Da wäre die erste Frage welche Hardware hast Du bereits jetzt zur Verfügung? Hast Du das RAM und die 4 HDD bereits? Spielt Geld bei Dir ggf. eine Rolle? :) Ich habe eben mal geschaut was so eine Minisforum N5 Air Kiste kostet und sehe da... -
Ttangshuai posted the thread May I ask if PVE supports the following operating systems in Proxmox VE: Installation and configuration.Red Hat Enterprise Linux 8 (64-bit) CentOS 7 (64-bit) Red Hat Enterprise Linux 7 (64-bit) Other 3.x or later Linux (64-bit) Microsoft Windows Server 2012 (64-bit) Oracle Linux 6 (64-bit) Red Hat Enterprise Linux 6 (64-bit) Oracle Linux 7 (64-bit)...
-
Llonger replied to the thread Second IP address on vmbr0.See: https://forum.proxmox.com/threads/assigning-an-additional-ip-to-the-host.146157/post-659351
-
ZHello, we need to config a second IP address on a PVE server to the existing bridge vmbr0 with has already an IP address. Have we to add it via CLI in /etc/networking/interfaces ? How to bind the webinterface/ssh etc to this second interface...
-
Ppoulpor reacted to snakeoilos's post in the thread Opt-in Linux 7.0 Kernel for Proxmox VE 9 available with
Like.
Kernel 7.0.0-2-pve will freeze the host if total free RAM becomes low (< 5 to 10% free). Any one seeing this issue? I just have to back off the RAM requirements for my VMs a little (now around 87% usage) and everything works again. Host do not... -
hi there i solved the issue thru flashing the rom and now the drives shows correctly. thanks -
JYou right, somehow I understood that there are SSD for OS but not SSD to dedicate to SD, so imagined that OP wanted to devote some space on those SSD for SD.
-
JThis is only HDD, zero SSD. (As of #1) Having a "separate" Special Device on the very same spindles makes no sense. Actually we know not much at all. What actual drives are available? How many? How many (unused) connectors has the controller...
-
JJohannes S replied to the thread [SOLVED] Does this update require a reboot?.With actual server hardware you are running it in a company and then you should have a cluster anyway if you need high-availability.
-
JJohannes S reacted to proxuser77's post in the thread [SOLVED] Does this update require a reboot? with Like.
You could try needrestart: needrestart man page By default, it runs in interactive mode, i.e. if you update from the CLI (apt update && apt full-upgrade), it tells you whether a reboot is necessary, lists all services that need to be restarted...
-
JMoin Da wäre die erste Frage welche Hardware hast Du bereits jetzt zur Verfügung? Hast Du das RAM und die 4 HDD bereits? Spielt Geld bei Dir ggf. eine Rolle? :) Ich habe eben mal geschaut was so eine Minisforum N5 Air Kiste kostet und sehe da...
-
JJohannes S reacted to J-Rod's post in the thread Has anyone tried Ubiquiti's ENAS for ProxMox's storage array? with Like.
For an EQ replacement on a tight budget, I probably would have suggested a used Dell PowerVault ME4 storage array, which supports the same Dell-rebranded hard drives as their PowerEdge servers. It also supports three tiers of storage, but not...
-
JJohannes S reacted to J-Rod's post in the thread [SOLVED] [Virtualizing PDM] Host PVE Node Uses ZFS Storage. When installing PDM inside VM, EXT4 or ZFS? with Like.
Side note: I do have an 18-drive bare metal TrueNAS server, an OpenMediaVault/SnapRAID/MergerFS server with 20+ disks of all sizes and interfaces, and a PVE server with a handful of drives with hundreds of media errors. All for...
-
JJohannes S reacted to J-Rod's post in the thread [SOLVED] [Virtualizing PDM] Host PVE Node Uses ZFS Storage. When installing PDM inside VM, EXT4 or ZFS? with Like.
Those posts are a dozen years old. The author also has over 18k posts on the old forums, so it's pretty clear they were drinking the FreeNAS Kool-Aid. There is going to be some bias. As mentioned, virtualizing FreeBSD is less common than...
-
JJohannes S reacted to UdoB's post in the thread Quick HOWTO on setting up iSCSI Multipath with Like.
You know that there are statements "out there" which declare iSCSI deprecated, right? Of course this is heavily exaggerated, but for new setups: choose wisely! Changing the storage system after the fact is... difficult - as you know...
-
JJohannes S reacted to n.frey's post in the thread [SOLVED] [PDM 1.1.x] New to PDM: How to Add Remote (Set Up User/Permissions)? with Like.
Definitely, we even mention it in our docs [0]: You can see the privileges for PDM here: [1]. If the user is on the PDM realm, it will for example prompt for a pam login on the web-shell and not directly be logged in as root (i.e. the user has...