intel

Hello! I am having a very strange issue that I'm not quite sure how to solve. On my PVE host (clean install) I can access the internet and ping things on my local network as well, as is expected. I can also ping guests but it seems to be very lossy, losing the first 3-5 packets and then randomly...

I'm having an issue with a network 'linux bridge' or 'bond' in PVE/Debian. I have recently migrated from ESXi 7.0u3 to Proxmox 8.4. I am NEW to Proxmox bonds/bridges but I 'think' I have set it up correctly. (?) I setup PVE 8.4 on a temporary old desktop with (1x 1G NICs and 2x 2.5G NICs) in...

I have an Intel CPU with embedded iGPU (i5 1335u) on my proxmox host and 16Gb of ddr5. In host bios, i can chose 128-256-512-1024 memory aperture for the iGPU. This amount of memory is later no more available in proxmox host (reserved) I wonder, if the GPU is shared between several VMs ( vGPU )...

Hi, total Proxmox newb here. I'm trying to get video output via HDMI from the machine running PVE, but I am having trouble figuring out how to go about it. I tried following this person's setup: [SOLVED] GPU Passthrough on fedora, but I had no luck just copying their setup. I don't know enough...

Hello. I'm trying to start a VM (Windows10 x64) with the following parameters args: -cpu 'kvm64,vendor=GenuineIntel' The VM doesn't start. But args: -cpu 'host,vendor=GenuineIntel' args: -cpu 'qemu64,vendor=GenuineIntel' It starts. In "Vendor" I see intel. But I need kvm64. When...

Hi, I want to buy a 2.5GbE NIC for my Proxmox servers. I wonder what would be a better choice... I was thinking about Intel I226-V. Supposedly there are fewer problems with it than Intel I225-V. Or maybe choose something with Realtek chipset? If so, which Realtek chipset works best with...

As the subject says, I have an Intel Arc A310 that I want to use in a VM via passthrough. Unfortunately, even though on other hosts I have been able to get nVidia GPUs passing through just fine, I cannot get this Intel card to work. On a Windows 11 VM, I able to get it not do the Code 43 error...

Hi everyone, I’ve been trying with setting up Open vSwitch w/ DPDK on my Proxmox server but I’m struggling to move the management port from eno1 (temporary) back to enp4s0 (LAN interface) OVS w/ DPDK. My Setup: eno1: Temporary Proxmox management port. Normally an unused port. [1GbE Intel NIC]...

Good morning! I'm completely green as it comes to glass. So I ordered the next hardware, hoping I understood enough from the info I gathered all over the place. 2 NIC's: Intel X520-DA1, 82599EN (https://www.amazon.nl/-/en/dp/B01GHTXHMK) Intel X520-DA2, 82599ES...

Hi All, I need some guidance on the final steps of configuring an iGPU for Plex as I'm not exactly sure how to pass it through from Proxmox. I'm trying to add an i7 iGPU from my Intel NUC to a Plex LXC and I can see the device on Proxmox, so that's good, but I'm not sure how to actually pass...

Hello! I did the offered updates today, 10th July 2024, which included Kernel 6.8.8-2 (Firmware 3.12-1 and a few other things), and upon reboot the host and VMs using one of the three NICs had no networking -- this was the NIC with the default gateway for the host box. I run a 13th Gen Intel...

Hi everyone, i'm having an issue that i don't know how to troubleshoute. I boucht an Intel optane u.2 disk, with the aim of passing it trough to Truenas. The u.2 drive works even if it is an ebay-used one (94% life left, so i will probably die before the drive). To test it, i've tried on a...

CPU: Intel i7-7700 GPU: Intel Graphics HD 630 & NVIDIA Geforce GT 730 Motherboard: ASUS Prime Z270-P Disk: WD SN750 & SKHynix PC711 I set IOMMU on and passed-through GT 730, NVMe PC711 and 3 USB Ports to a Windows 10 LTSC guest machine. Whenever I reboot my guest machine, the iGPU of host will...

Hello. I'm in the process of standing up a new Intel i9-based cluster and would like to migrate the VMs over from the current AMD Epyc-based hosts. I'd like to avoid rebuilding the VMs from scratch if I can help it. Here are some facts I think will be helpful. All VMs were created in...

While experimenting with GPU passthrough I could not configure to VM in Proxmox, as instructed by this guide from Intel, I'm having trouble figuring out how to properly configure the `-device` in an existing VM in Proxmox. According to their instructions, the guest VM should be configured as...

Hello all, I recently deployed a Debian VM to install the Ubiquiti UniFi Controller Software as I switched out my RAX2000 router for a UniFi U6 Mesh AP. I was able to get the UniFi software and the AP installed successfully, however, there seems to be an issue with the speeds. I installed...

Hello, I have this specs: CPU: i5-14500 iGPU: UHD Graphics 770 GPU: NVIDIA Geforce GTX 1660 Super Proxmox: ver.8.1.10 ----- - I enabled IOMMU as described HERE - I need fully passthrough my GPU NVIDIA to one of my VM. It works - I lost in PVE access to /dev/dri/D128 Now, I cannot use VirtGL or...

Hallo Leute, ich möchte meine Grafikkarte an eine Windows11 VM durchreichen und komme nicht weiter. Vielleicht ist ja jemand so freundlich und schaut sich das mal an. Zur Situation: UEFI Settings: Intel (VMX) Virtualisation Technology - enabled VT-d - enabled 1. Anpassung der Datei...

Hi, i am trying to understund why the system behave this way to find out where the issue lays, system specifications and and steps taken in attempt to fix it bellow: CPU: G4400T / I5 6500 (tried both) RAM: 16GB (2x 8GB) Motherboard: ASRock H110M-DGS R3.0 (BIOS: P7.4) NetworkPVE: RTL8111 GbE...

Hello I have installed Proxmox VE on an HP EliteDesk 800 G3 CPU: Intel i5-6500 65W Chipset: Intel Q270 As per intel specs (available at https://www.intel.com/content/www/us/en/products/sku/88184/intel-core-i56500-processor-6m-cache-up-to-3-60-ghz/specifications.html ) the CPU supports all this...