debian

We have been using ceph on our Proxmox (uptodate) with version 19.2.0 as in: sudo ceph --version ceph version 19.2.0 (16063ff2022298c9300e49a547a16ffda59baf13) squid (stable) But our radosgw server was running on Debian, and, we just discovered recently that the version used there was not...

So I have a remote test rig that i have been running Debian on, just testing some different setups. The only thing installed was Debian 12 with Docker with a few containers and Samba. I decided to try Proxmox following this guide...

I have a consistent repro of a kernel panic, seemingly occurring due to something between cloud-init and Proxmox running 8.3. Likely not something your average user will find, as it requires expanding a disk on first install (whereas most click-ops would be the ISO installer, I assume). My...

Good evening, I have a 2018 Mac Mini running proxmox 8.3.2. I've recently attached a thunderbolt eGPU with an NVIDIA 3070 GPU. I've followed countless guides, forum posts, etc. to try to get this working in a Debian 12 VM, to no avail. I can get the passthrough "working" as far as the GPU...

Hi there friends! I'm attempting to move off ESXi on a server (surprise, surprise), and one of my VMs is being particularly petulant. It's a Debian 12 VM, running a pretty standard LAMP stack, set up to boot with UEFI. I tried moving it with the ESXi Import function, and when I did, it sends...

I restored a Debian LXC with xorg from a Qotom firewall appliance to a Beelink EQR6 mini-pc, and the original has swap while the restored LXC does not. Have tried resizing swap in PVE GUI and with ' pct set 101 --swap 384 ' and the like, and the container still has 0 swap Beelink PVE 8.3.1...

Hi, I am struggling to find a single definitive answer to this. I've been tasked with commissioning a new cluster of 50x servers. I wish to deploy Promox to install in an automated manner via a PXE server. The official instructions on automation seem to to focus on creating a customised...

Dear Proxmox community, I've been trying to passthrough the iGPU of a Intel NUC7u5DNH to a Debian VM without success. lspci gives the following: 00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics 620 [8086:5916] (rev 02). dmesg detects and adds the PCI device [ 0.366384]...

I'm experiencing sporadic but reoccurring issues with one of my VMs. One VM has a super high load average. top works sometimes, htop completely hangs. SSH sometimes works. top shows basically no CPU usage. This setup worked without issue for the last 3 months. This started about a week ago. I...

Hello, I would like to set up an environment with multiple VMs running on a single server and assign an individual static IP for each of the VMs. The main server would be connecting to a single router with a public static IP. Is there even a way to do this? I am new to this so apologies if this...

Hi, I have a Nvidia 3090 that is passed through into a Debian VM (for running LLM). I want to perform scheduled backup for this VM. In Proxmox web UI, I clicked "datacenter", then created a backup job ("stop" mode) that runs at 6am every day. It worked on the first day, but the backup job...

Hello everyone, I've just installed Proxmox on Debian 11 following this official guide. I wanted to create a VM but there's no bridge available in the network configuration. This is my /etc/network/interfaces: source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo...

Hi so i have one old CT container, that can access the network just fine But when i create a new one it manages to get an IP but that is about it.. Working CT Broken CT pct config 210 arch: amd64 cores: 4 features: nesting=1 hostname: emby memory: 2048 mp0: /storage/movies,mp=/mnt/movies...

Hello, I’m experiencing several issues with my Proxmox setup and VM backups. Here are the details: Environment: Proxmox VE with multiple Debian VMs. Backups are scheduled daily at 5 AM using the "stop" mode. Problem: After backups, approximately one in four VMs exhibit strange behaviors...

Hello proxmox community, it's my first thread here, and unfortunately it's an issue which i can't solve. I've been running a regular debian server for a few years. This have worked for me fine for some time, but due to need to run linux + windows server next to it, and also my lab needs have...

pveversion is at the bottom to save time for people looking only for the fix. Generally I do not use apparmor on my containers and I find them suitably secure as they are. But recently I experienced a situation where I had to get apparmor working, if not just temporarily. During the...

Hello all, I recently deployed a Debian VM to install the Ubiquiti UniFi Controller Software as I switched out my RAX2000 router for a UniFi U6 Mesh AP. I was able to get the UniFi software and the AP installed successfully, however, there seems to be an issue with the speeds. I installed...

Hello! I'm currently running Proxmox 8.1 and originally had a Ubuntu Server VM set up for months, which I've loaded data on my hard drive in path /mnt/WD14-1 through two separate virtual disks (/dev/sdb1 mounted to /mnt/WD14-1/sdb1/, /dev/sdb2 mounted to /mnt/WD14-1/sdb2/). I just created a few...

Hi, I set um the Proxmox Offline Mirror successfully, and connected my nodes with it. My question is fairly simple: To keep my nodes updated (and most importantly all security holes patched), do I need a snapshot of the Debian repository, too? Right now I only snapshotted (meaning syncd and...

Setup: - PVE Cluster 8.1.0 / Linux 6.5.13-3-pve - Typical Proxmox installation with bridged WAN (Linux Bridge) Test VMs: #1: Debian 12 - Kernel: 6.1.0-18-amd64 - IP & Mac Filter enabled (NDP enabled) - Firewall: Block all Incoming (except ICMP Test server ip) / Allow all outgoing - Network...