bonded network

Here's my config, and forgive me, I'm an "old" vSphere admin: auto lo iface lo inet loopback iface eno1 inet manual iface eno2 inet manual auto ens2f0 iface ens2f0 inet manual auto ens2f1 iface ens2f1 inet manual auto bond0 iface bond0 inet manual bond-slaves ens2f0 ens2f1...

Hi I have tried to bond 2 network interfaces and it looks like it works. I have done the same on the switch and my synology. My problem is that the speed has not changed. I would have expected a 2Gbit between the 2 machines. What am I missing?

hi, I installed two Mellox network cards of 10 gbit each, but when I make the bond with the two network cards the maximum speed is 9 gbit, always the same dedicated if I install windows and configure lcap the connection speed is 20 gbit, so the cards work correctly, how do I solve the problem on...

Hello All, I live at home with my parents while I finish school, so I cannot set up my home network as I would prefer, but I am trying to work on my home in any way I can. I recently set up a pfsense VM on my home lab, and I have successfully gotten it connected to my main PC and an AP so that...

good morning, have installed Proxmox VE 7.4 I am not able to do the following configuration with OVS. I have two cards eno1 and eno2, I need them to be in LACP bonding. These cards have vlan10 as their native VLAN and others such as vlan20 for the rest.I have tried the settings in the...

HI, I'm trying to setup an alternative NIC for administration. auto lo iface lo inet loopback auto enp3s0f0 iface enp3s0f0 inet manual auto enp5s0 inet manual auto enp3s0f1 iface enp3s0f1 inet manual auto bond0 iface bond0 inet manual bond-slaves enp3s0f0 enp3s0f1...

I look for support and guidance around where I am going wrong in a PROXMOX environment that I am setting up. I have one server that is connected and working for the Test Environment. It is running on the 172.16.0.15/16 network. We have three more servers that we have set up in cluster. The...

Hallo Zusammen, ich habe dazu nichts gefunden. Mein Proxmox-Server hat zwei Netzwerk-Karten und diese sind mit Bond Verbunden. Jetzt wollte ich die Wake on Lan Funktion aktivieren. ethtool installiert und die eno1 unter interfaces eingetragen. Das funktioniert auf dem 2ten Server mit nur...

Moin Bin grad am Testen mit einem DELL Server mit 2x 10Gbit Ethernet Schnittstellen. Wollte einen Bond einrichten, das ganze als active-backup. Untenstehend die /etc /network/interfaces. Nur der Port, der als Primary gewählt ist, funktioniert dann. Wenn ich einfach mein Patchkabel umstecke...

Hi, aktuell treibt mich die Konfiguration in den Wahnsinn. Setup: 3x Lenovo M720q als Cluster Onboard ist jeweils ein Intel I219-V verbaut Ich habe nun jeweils noch eine CX311A - ConnectX-3 SFP+ verbaut. Die Mellanox laufen über einen Unfi Aggregation Switch und die Intel Ports über einen Unifi...

Hi all, I've configured the following ethernet bond [bond0], which appears to be working when both [eth0] and [eth1] are online, however, when I take down [eth1], IPv6 stops pinging for the node but not in the VMs. When I put [eth1] back online and take down [eth0], IPv6 is up for the node but...

Hi Guys This is my very first post and having had a 5 day workout with proxmox I have found a problem mentioned all over and that is the network that does not become active on a Windows 10 VM. I tried everything to get it to work, but wait, let me first tell you what I am running: Intel NUC...