Search results

I have solved this: The 4 networking ports on the server show up as eno5 to eno8. The networking port that got assigned to vmbr0 was enp193s0f4u4 (Maybe the ILO port?) I assigned eno5 to vmbr0 and everything started working. Thanks for your help.

From the ISO

Hello I have just installed ProxMox 6.3-1 on this server: HPE ProLiant DL325 Gen10 7232P The network controller is: HPE 1Gb Ethernet 4-Port 336FLR Adapter The installation went fine but the networking does not seem to work. The lights do not even light up on the network ports. Does anyone...

That works! thank you Nemesiz.

I did a fresh install of proxmox with zfs as the root filesystem with 2 mirrored disks (raid 1). I am trying to use setfacl in a container but I get operation not supported. Is there any way to enable acl in a container? I am trying to run samba4 in the container and it needs acl support.

Thanks Tom It all works perfectly now.

Here is my setup:

I get this error when I try a snapshot backup: INFO: starting new backup job: vzdump 100 --remove 0 --mode snapshot --compress lzo --storage backup --node vmh INFO: Starting Backup of VM 100 (qemu) INFO: status = running INFO: mode failure - unable to dump into snapshot (use option --dumpdir)...

Re: kernel: EXT4-fs (dm-3): Unaligned AIO/DIO on inode 130479 by kvm; performance wil Have you found anything on this? I have the same errors in my log. I Installed with the CD but migrated to a Raid 1 setup with ext4 afterwards.

I actually found this answer on Google finally: The container is not necessarilly unmounted when it is shutdown. When the container is started it is first unmounted and then remounted hence the running 101.umount. All I did was put exit 0 at the end of the 101.umount script. 101.umount...

I am running proxmox 2. When I use the 101.mount script it seems to work well but If I put a 101.mount and a 101.umount script in /etc/vz/conf it tries to run the umount script when the container starts and it fails because the shares are not mounted: 101.mount: mount -t smbfs -o...

Have you been able to find out which kernel versions this will work with. Alternately I could try pci pass through again although I did try it a bit with 1.8 and had a couple of occasions where the guest became unresponsive to the point that I had to reboot the proxmox host. Maybe 1.9 will have...

No it didn't work with 1.8 either.

I have A windows 7 guest running on proxmox 1.9. The guest runs some software to link to some industrial control via rs485. Normally we run this with a serial port and a rs232 to rs485 adapter and it works fine on windows 7. After building a win7 guest and putting: "serial: /dev/ttyS3" in the...

tom Last night the cron job failed again. This morning I opened up the VNC terminal and the machine shutdown again. One thing that I did not mention is that I do not even need to log into the win64 guest for it to shutdown -- just open a vnc terminal. I checked the logs and there are not...

I just tried it now. It had been up for a few hours and would not shut down. As soon as I logged in it shutdown. However, I then closed the vnc terminal and started the machine with the terminal closed. After it had run a few minutes I tried to shut it down without logging in and it worked fine...

when I run the following command: vzdump --quiet --stop --compress --storage usb_backup --maxfiles 3 --mailto somename@example.com 132 I get the following: 132 win64 FAILED 00:10:02 command 'qm --skiplock shutdown 132 && qm wait 132 600' failed with exit code 255 However, when I try to...