Search results

Team, I'm struggling with 2 (out of 4) Ubuntu VM's. The vlans in these are not working as expected (i.e. eth0.122 and eth0.123). The output of "ip link" looks fine to me - the same applies for "ip a". However, pinging the defailt gateway for both vlans is not working. Everything works fine via...

I recently upgraded from Proxmox 7 to 8. Within that upgrade, the systemd-resolved was removed. I reinstalled this with the stub-resolver enabled - the same way it was previously. In fact - the original systemd-resolved config-file was not removed. However the caching (i.e. stub-resolving)...

Team, I'm trying to build a LXC container with a few network services like docker, pihole and chrony. The build went as expected. However, after a reboot, there is a little over 5 minute delay when starting these services. Using debug mode of pihole reveiled the following message: Jun 26...

Team, I just finished an upgrade - replacing an Asus B450 with an Asus B550. This includes a CPU replacement: the Ryzen 1600 is replaced with a Ryzen 5700X. After some config changes in the BIOS the system boots as expected. And after changing the network config (i.e. /etc/network/interfaces)...

Team, The file /var/log/syslog and console screen is flooded with these messages: vmbr0: received packet on eno1 with own address as source address (addr:08:60:6e:7d:18:fe, vlan:1010) The current settings of vmbr0: auto vmbr0 iface vmbr0 inet dhcp bridge-ports eno1 bridge-stp...

Team, Part of the output of "ip a" looks like this: 19: vmbr1v999: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether d2:75:49:62:ca:8c brd ff:ff:ff:ff:ff:ff 20: enp3s0f1.999@enp3s0f1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc...

In my lab I'm relying on cifs/samba for backup and deploying vm images. The NAS behind it is switched-off between 11 PM and 7 AM. The syslog is then filling rapidly with messages like "pvestatd[1734]: storage 'backup-only' is not online". Is there a way to disable this type of monitoring for...

I have read several topics on disabling IPv6 in a LCX container. And made changes to /etc/sysctl.conf being: sysctl net.ipv6.conf.all.disable_ipv6=1 sysctl net.ipv6.conf.default.disable_ipv6=1 This was done for the Proxmox hosts, the VM's and the LCX containers. But still... within the LCX...

Earlier this evening I tried renaming 2 standalone hosts. One worked out as expected - the other did not. Meaning the folder /etc/pve was empty - not sure if any other damage was done. I compared the 2 hosts and was able to re-create some bits and pieces: - Recreated the folder structure and...

I'm running a multi-node Proxmox-based playground for software testing and security analysis. And looking for a way to create a single management UI for up to 5 Proxmox nodes. Ideally having access to this management UI via a reverse proxy; part of which runs via Cloudflare. This means that...

Not sure if this is Proxmox related - but the log has lots of these messages: Cannot send LLDP packet for <something>, Too big message Any suggestion where this is coming from? An what to do with this? With warm regards - Will

Hi *, I have converted vmdk images into qcow2 images. When I try to import them, they are imported as raw image. However, when I create a new vm with new disks, these disks are created as a qcow2 images. Both are created on the "local" storage. Which points to /var/lib/vz. This /var/lib/vz is...

Team, The mail-log /var/log/mail.log is full with messages like: "postfix/smtp[282864]: CE97B7803B2: host mail.it-visibility.net[188.68.47.56]" "postfix/smtp[282864]: CE97B7803B2: to=<alerts@it-visibility.net>, relay=mx2f38.netcup.net" However, these two don't show up in the postfix-config...

Hi *, See also attached screenshot: I can see that the disk-images are still there. And the VM's are still running since the applications are working as expected. But still - where the VM(-configs?) residing? Any suggestions to get them back? This situation happened while playing around with...

Hi *.*, For performance reasons I would like replace the 2-TB SATA-disk with a 2-TB NVME-SSD. The idea was cloning the SATA-disk to the NVME-SSD with CloneZilla. This didn't work because the NVME-SSD is about 100-Gbyte smaller then the SATA-disk. The outcome of lsblk-results shows the...

Hi Team, I have a basic Proxmox install with a single, 2-TB SATA-SSD. For performance reasons I would like to replace this with a 2-TB NVME-SSD. The current partitions are shown in the list below. The idea was to use CloneZilla for this transition. That approach fails because as seen in the...

Everybody, I'm looking for a way to do the following: - use a seperate/dedicated disk for Proxmox; including the swap partition => for example sda - use a 8 TBytes RAID-volume for all the running VM's => for example sdb - use a caching SSD => for example sdc Anybody suggestions for making this...