Search results

Yes version 6. I have disabled hardware raid and have each disc configured in AHCI mode. Yes - I mean with proxmox installer ZFS RAID1. I will play around with my power settings see if this changes. I've read this is a standard error and can be ignored. Both drives are SATA. My intention is...

After installing PVE as RAID1 i get the below errors on boot. Are any of the the below errors a concern? Specifically the ones that mention 'no caching mode page found'? no caching mode page found assuming drive cache: write through

Hardware/drive failure is not so important for my installation. Initializing clustering + CEPH will give me the redundancy I need. The data on the VMs is not critical. CEPH provides the redundancy through OSDs, correct? It's more vital that I have more storage. Would RAID 0 be adequate? Should...

thank you for the help.

Hello, I have 2 SATA drives both 1TB. What is the best option for a proxmox installation with CEPH + cluster. Which option runs the most stable? Both drives are setup on my server as AHCI with hardware raid disabled. Would zfs (RAID 1) be the best option? Do any of these advanced...

I'm working on getting a cluster setup, and need to create policies in a firewall to allow the traffic. What services are required for Corosync and CEPH to operate correctly? What ports are required?

here is the output root@broccoli:~# qm status 101 --verbose balloon: 2147483648 ballooninfo: mem_swapped_in: 0 last_update: 1566054644 minor_page_faults: 140641 total_mem: 2101727232 free_mem: 934707200 max_mem: 2147483648 actual...

There are no errors. I think the node ran out of space. I deleted some VMs, but the free space on the node has not recounted. I restarted the node as well. https://imgur.com/eJOiUiV

Hello, My VM was working fine but i woke up to an exclamation mark and my VM is unresponsive. What does it mean? . https://imgur.com/TUMVeOz

Hello, I've gotten the O_DIRECT error when starting VMs. I have (1) SSD at 232gb and (1) 1tb disk drive. I configured as RAID 0 just to get things going as I will be changing my configuration in the future. I read in the documentation to enable write back to stop the O_DIRECT error. This...

I did a fresh install redirected the repositories updated and didn't have any issues.Thank you forum for the help.

Thank you. After doing some research i blacklisted both below modules. Proxmox already came with the first module blacklisted. Blacklist nvidiafb Blacklist acpi_power_meter Blacklist pcspkr Any help on the postfix failure?

I've been able to find that the driver 'pcspkr' has been resolved, but I'm not sure about the first error. I found a previous post from someone who also had the same issue. I'm installing on an R320. https://pve.proxmox.com/pipermail/pve-devel/2014-October/012995.html

I converted the drives to non-Raid set SATA to AHCI. I rebooted the computer and the system kicked my raid card back on and reset my configurations to RAID ON with 2 virtual RAID drives. I rebooted again disabled the lifecycle controller followed the same process of configuring the RAID card and...

Okay. I will convert them to non-RAID and set sata to AHCI. Thank you!

Thank you. Should I convert to to non-raid drives? Why is AHCI the preffered method?

Hello, I purchased some refurbished R320s. RAID can be configured in the bios and I'm not sure of the correct SATA mode to select in the BIOS. The server has 2 HDDs, and came with windows server 2016 pre installed. I'd like to setup a few nodes and eventually configure ceph but I will be...

I'm not really understanding the answer here.

I dont need to add the bridge with netwoker manager, etc. I only need to update my interface file with the below? I do not have a eno1 device. The only device is ens18. I need to add a network device to my VM? auto vmbr0 iface vmbr0 inet static address 192.168.1.129 netmask 255.255.255.0...

Hello, Trying to get access to my VM through SSH from my local computer on the same network. My local computer can ping the VM but the VM cannot ping my local computer. I'm very new to this, but have been trying to learn. I see vmbr0 in the network GUI on my node. should the correct...