Search results

  1. Ma907xb

    boot errors

    After installing PVE as RAID1 i get the below errors on boot. Are any of the the below errors a concern? Specifically the ones that mention 'no caching mode page found'? no caching mode page found assuming drive cache: write through
  2. Ma907xb

    Correct initial installation w/ CEPH

    Hardware/drive failure is not so important for my installation. Initializing clustering + CEPH will give me the redundancy I need. The data on the VMs is not critical. CEPH provides the redundancy through OSDs, correct? It's more vital that I have more storage. Would RAID 0 be adequate? Should...
  3. Ma907xb

    Proxmox - Corosync & CEPH

    thank you for the help.
  4. Ma907xb

    Correct initial installation w/ CEPH

    Hello, I have 2 SATA drives both 1TB. What is the best option for a proxmox installation with CEPH + cluster. Which option runs the most stable? Both drives are setup on my server as AHCI with hardware raid disabled. Would zfs (RAID 1) be the best option? Do any of these advanced...
  5. Ma907xb

    Proxmox - Corosync & CEPH

    I'm working on getting a cluster setup, and need to create policies in a firewall to allow the traffic. What services are required for Corosync and CEPH to operate correctly? What ports are required?
  6. Ma907xb

    Exclamation mark on VM

    here is the output root@broccoli:~# qm status 101 --verbose balloon: 2147483648 ballooninfo: mem_swapped_in: 0 last_update: 1566054644 minor_page_faults: 140641 total_mem: 2101727232 free_mem: 934707200 max_mem: 2147483648 actual...
  7. Ma907xb

    Exclamation mark on VM

    There are no errors. I think the node ran out of space. I deleted some VMs, but the free space on the node has not recounted. I restarted the node as well. https://imgur.com/eJOiUiV
  8. Ma907xb

    Exclamation mark on VM

    Hello, My VM was working fine but i woke up to an exclamation mark and my VM is unresponsive. What does it mean? . https://imgur.com/TUMVeOz
  9. Ma907xb

    O_Direct Error - Write through / Write back

    Hello, I've gotten the O_DIRECT error when starting VMs. I have (1) SSD at 232gb and (1) 1tb disk drive. I configured as RAID 0 just to get things going as I will be changing my configuration in the future. I read in the documentation to enable write back to stop the O_DIRECT error. This...
  10. Ma907xb

    Proxmox - R320 raid dell perc s110

    I did a fresh install redirected the repositories updated and didn't have any issues.Thank you forum for the help.
  11. Ma907xb

    Proxmox - R320 raid dell perc s110

    Thank you. After doing some research i blacklisted both below modules. Proxmox already came with the first module blacklisted. Blacklist nvidiafb Blacklist acpi_power_meter Blacklist pcspkr Any help on the postfix failure?
  12. Ma907xb

    Proxmox - R320 raid dell perc s110

    I've been able to find that the driver 'pcspkr' has been resolved, but I'm not sure about the first error. I found a previous post from someone who also had the same issue. I'm installing on an R320. https://pve.proxmox.com/pipermail/pve-devel/2014-October/012995.html
  13. Ma907xb

    Proxmox - R320 raid dell perc s110

    I converted the drives to non-Raid set SATA to AHCI. I rebooted the computer and the system kicked my raid card back on and reset my configurations to RAID ON with 2 virtual RAID drives. I rebooted again disabled the lifecycle controller followed the same process of configuring the RAID card and...
  14. Ma907xb

    Proxmox - R320 raid dell perc s110

    Okay. I will convert them to non-RAID and set sata to AHCI. Thank you!
  15. Ma907xb

    Proxmox - R320 raid dell perc s110

    Thank you. Should I convert to to non-raid drives? Why is AHCI the preffered method?
  16. Ma907xb

    Proxmox - R320 raid dell perc s110

    Hello, I purchased some refurbished R320s. RAID can be configured in the bios and I'm not sure of the correct SATA mode to select in the BIOS. The server has 2 HDDs, and came with windows server 2016 pre installed. I'd like to setup a few nodes and eventually configure ceph but I will be...
  17. Ma907xb

    Proxmox Bridge

    I'm not really understanding the answer here.
  18. Ma907xb

    Proxmox Bridge

    I dont need to add the bridge with netwoker manager, etc. I only need to update my interface file with the below? I do not have a eno1 device. The only device is ens18. I need to add a network device to my VM? auto vmbr0 iface vmbr0 inet static address 192.168.1.129 netmask 255.255.255.0...
  19. Ma907xb

    Proxmox Bridge

    Hello, Trying to get access to my VM through SSH from my local computer on the same network. My local computer can ping the VM but the VM cannot ping my local computer. I'm very new to this, but have been trying to learn. I see vmbr0 in the network GUI on my node. should the correct...
  20. Ma907xb

    USB install better options (needed!)

    Does anyone have a guide to follow? https://pve.proxmox.com/wiki/Install_from_USB_Stick This recommends https://www.balena.io/etcher/ When i download and load the file into etcher i get a warning https://imgur.com/AES3RTk

About

The Proxmox community has been around for many years and offers help and support for Proxmox VE, Proxmox Backup Server, and Proxmox Mail Gateway.
We think our community is one of the best thanks to people like you!

Get your subscription!

The Proxmox team works very hard to make sure you are running the best software and getting stable updates and security enhancements, as well as quick enterprise support. Tens of thousands of happy customers have a Proxmox subscription. Get yours easily in our online shop.

Buy now!