Search results

Hi bartl, simple :) I will try it. thx An other idea. Can i make a 2 node cluster with old 3x und 4x and simple switch over to the 4x?

Hi, i have an old Debian Wheezy single Proxmox in Version 3.4-13 (3.10.0-1-pve). I have a few KVM VMs on it. I now setup a new Machine with Proxmox VE 4.2. The Question is how can i migrate the VMS from old 3.4 to new 4.2? thx

Hello Udo, its a single disk and all is on that. The check reports: 40961 leaked clusters were found on the image. This means waste of disk space, but no harm to data. 65536/65536 = 100.00% allocated, 0.65% fragmented, 0.00% compressed clusters Image end offset: 4370006016 so it looks good. But...

Hello, i use latest pve-manager/3.3-5/bfebec03 (running kernel: 3.10.0-1-pve). i have a kvm with qcow2 disk which runs since installation without problems. i know have to reboot this vm and run into trouble. Message in boot: trying to mount root from ufs:/dev/ad0s1a - warning. / was not proberly...

Ah ok. I know i ask a lot but i am interested in pve and want to understand whats going why on... Can you say why this is an exception? If so it would break with the hole concept of stable, testing ....

Hi Dietmar, thanks. As i use debian stable i thought i see only stable packages, but thats it - i use the repo from pve so i see not only stable but also all available kernels, testing perhaps too. that means that as i upgrade pve to 3.x it installed latest stable kernel 2-6x, but in repo i can...

Ah ok. And would it be a good idea to use the last kernel version?

Hi, thanks for your answer. Can you explain the steps, why should i do so? Why download it from proxmox while it is in repo too? I whould simply install it via aptitude install pve-kernel-3.10.0-1... - should be the same. But why do i have pve 3.2 but Kernel 2.6?

Hello, i upgraded successfully to PVE 3.2 on my wheezy. Now i saw that Kernel 2.6.32-27 is installed but i could install pve-kernel-3.10.0-1-pve via repository. a apt-get dist-upgrade didnt install this kernel. can some one explain it to me? and could i simply install the newer kernel?

Hello, is there any solution? i have the same with usb nic on wan connected. first the kernel.log say entering forwarding state and than entering disabled state and i cant connect through this nic. if i reboot the whole machine all is ok.

Hi Tom, ok but i think thats not as special, because i want to simply use a second eth only for pppe out of vmbr. And the question about security is, how to configure the second eth and the vmbr for the virtual machine. should i use the vmbr still as bridge and configure the vm with nat or must...

Hi, i want to use pfsense as firewall and for my wan ppoe nat configuration. actually i have configured in proxmox 2 nics vmbr0 for lan (192.xxx) and vmbr1 (10.xxx) for wan both as bridge network. in pfsense i have two nics as bridge too, net0->vmbr0 and net1->vmbr1. my question is about...

Hi, i played around with some qm commands. As i used qm status <id> -verbose i get info with maxmem: and mem: . Ok maxmem is the maximum of memory the kvm can use. So i would suggest mem: is the actual using memory by the kvm. But if i have a look at it. The systeminfo in gnome desktop say less...

Hi, ok i understand. As far as i saw std or vga are only for kvm, which explain all ;)

Hello, i updated my Debian Squeeze to Wheezy in OpenVZ with Cirrus Logic GD 5446. After that i cant start gnome with error "Failed to load session "gnome"". Actually i think its a driverproblem in PVE. Can you help?

Hello Udo, nice location where you life ;) sadly i cant write an pn to you. The firewall is just for testing, the final will run standalon on a system. If i understand it right, i dont should configure the ip adress of the wan on the pve host, i should create a second bridge in pve and enter the...

Hi, i use acutal 2.3 and want to install a second nic for wan. now i want to understand how secure is proxmox and the build of the internal routing/bridging. e.g. for wan2lan: wan-router 10.0.0.1->proxmox 2.nic with firewall on 10.0.0.2 <->and proxmox with kvm clients in 192.168.0.x and first...

Hello, i am not a security or network specialist, but i want to install pfsense in an kvm on my proxmox 2.3. my initial idea is to use a second nic for the wan/internet and the first for my internal clients. now after some searching i saw that i can also use the one nic for routing and...

Hello dietmar, are you on holidays ;)? i think i notice today. i use for my homecinema a filecluster. these machines are all stand alone and have nothing directly to do with proxmox, but the master of the cluster runs on a kvm vm. actually i play a blu ray disk and see with "vnstat -l" that the...

Sorry for missing informatin: OS ist on all Systems Debian Squeeze.