Recent content by ghstudio

I've spent the last hour following dead ends but I would like to use the HDMI output on M70Q for my windows 11 video. I do not have an add on graphics card, so I'm trying to use the intel 630 built in to the M70Q. I have windows 11 running fine using remote terminal support or through the...

I am currently running Home Assistant (production) and WIndows 11 (test/development) on my Nuc8i5. I run windows 11 remotely from my desktop..if I need to access it directly from the NUC, I use the proxmox console function. Home Assistant just runs and is managed remotely. I would like to set...

I would like to set up my nuc with proxmox and use my desktop display in a VM. I currently have proxmox assigned to the desktop display. Is it possible to set Proxmox to use a USB/hdmi adapter?? If I can do that, then I should be able to assign the builit in adapter to the VM....I hope :)

I have proxmox 7.x installed on a nuc8 with 32gb and 1TB NVME. All is well, running windows 11, home assistant,.... I just put a 1tb sata drive in the NUC and would like to use it for backup. I'm a bit of a newbe at this. How do I activate that sata drive to do the backups? If I kill...

I have a NUC8 set up with windows 11 for testing....and I use windows 11 operationally on my desk. I would like to access the windows test system on the NUC using RDC from my desktop. I've enabled remoted desktop connection and I've checked that it's passed through windows defender. the...

Is it possible to assign proxmox graphics to a usb/hdmi adapter and assign the internal graphics on my NUC8 to my hackintosh VM? If so....pls point me to some "how to do this" page.

I have multiple VM's and LXE's working on my NUC with Proxmox 7...and everything worked fine yesterday. This morning, I can no longer get to IP:8006 but all of the VM's are working fine with full LAN access. Looking at my router, I see all of the VM ip's, but I don't see Proxmox itself or...

How do I see all of the network IP's being requested by proxmox? I deleted an LXC and installed the same software on a new (different number) CT.....but after rebooting both my router and proxmox system, I still see the old IP assigned and active when looking at the router. I have the...

I am trying to run home assistant and pfSense on the same system (NUC8i5). Home Assistant uses a USB z-wave dongle...and pfSense is using a startech USB dual NIC. Each runs fine alone. If I start both of them, at some point minutes to hours later, Home Assistant loses contact with the z-wave...

I am trying to install windows 11 on Proxmox 7.1 on a NUC8i5. however I am unable to select where I want windows installed. I found a driverdisk (red hat?) and loaded the vioscsi AMD64 drivers but those drivers still don't show any disk to load windows. What drivers should I use to install

closed

I've installed Proxmox 7.1 and set up a new VM. Doing the install off a USB stick. I get the following error message. BdsDxe: failed to load Boot0003 "UEFI Misc Device" from PciRoot(0x0.......... I'm pretty new to proxmox and followed a "cookbook" with win11 on my USB stick...and I've...

I am trying to essentially the same on a NUC8i5. 1) Debian/Kodi or Libreelec with HDMI audio 2) Home Assistant (supervised) 3) some network storage capability (all I really need is Samba) which I can install as part of Home assistant 4) PfSense for network VPN security I am running 1, 2 and 3...

The only "fix" I've found is to run proxmox under debian (NUC7i5). I would still like to find a way to install proxmox with Debian/Kodi running it's own VM.

I'd like a solution as well.....I want to run Kodi under Ubuntu so I get Kodi 18. Only Kodi 17 is supported under Debian.