Latest activity
-
Ddaanw replied to the thread proxmox-kernel-7.0.2-6-pve failing network service.Are you sure the 7.0.2 log is complete?
-
Ffranzz posted the thread Auto sync guest time after rollback of VM snapshot with RAM/state in Proxmox VE: Installation and configuration.When rolling back a VM snapshot that includes RAM/state, the guest resumes with the old in-guest clock from the snapshot time. This is problematic for AD/Kerberos, databases, logs, monitoring, certificates, clusters, scheduled jobs, and any...
-
HHammyHavoc reacted to lazynooblet's post in the thread [SOLVED] PBS 4.2 using S3 via RustFS; anyone else? with
Like.
I got impatient, and have instead got PBS running directly on the Synology. So I won't be using S3 anymore. -
Kkodamap replied to the thread SDN zone shows "pending" on peer nodes after node reboot (9.2.x).Thank you for the explanation. Just to confirm my understanding — if we are using an OVS Bridge, it cannot be set to VLAN-aware, so there is no way to avoid this issue in an OVS-based setup, correct? Also, I tested setting only the Linux bridge...
-
SSunilkumar reacted to daveanderson's post in the thread Broadcom BCM57504 (100G) bnxt_en TX timeout and NIC reset on Proxmox 8.1.5 — while BCM57414 (25G) works fine on same host with Like.
/etc/network/interfaces contents: Basic gist is: two LACPs, each containing two of the ports, each nic has one port for each of the two LACPs (thus a nic card dying entirely should be ignored) of those two bonds: po7 / bond0 is for use by VMs...
-
SSunilkumar reacted to shanreich's post in the thread Broadcom BCM57504 (100G) bnxt_en TX timeout and NIC reset on Proxmox 8.1.5 — while BCM57414 (25G) works fine on same host with Like.
Could you post your full network configuration? I've seen several reports now and usually they were using some BCM cards with bonds and VLANs, but I couldn't yet tie them together... cat /etc/network/interfaces
-
SSunilkumar reacted to daveanderson's post in the thread Broadcom BCM57504 (100G) bnxt_en TX timeout and NIC reset on Proxmox 8.1.5 — while BCM57414 (25G) works fine on same host with Like.
we had a full kernel panic (eventually) on pve 9.1.x on kernel 7.0.0-3-pve due to wedged driver on a similar card, BCM57508. topology: each node has two dual 100g port cards, and each node has two lacp bonds, one for front of house networking...
-
SSunilkumar reacted to EllerholdAG's post in the thread Broadcom BCM57504 (100G) bnxt_en TX timeout and NIC reset on Proxmox 8.1.5 — while BCM57414 (25G) works fine on same host with Like.
Weve got two clusters of 3 servers, each with a BCM57504 100 GBe Dual Port in it and it is used for the ceph network with full mesh routing (no switches). I think we started with PVE 8.3 and are now up to 9.1.4 and never had any problems.
-
SSunilkumar reacted to walissongois's post in the thread Broadcom BCM57504 (100G) bnxt_en TX timeout and NIC reset on Proxmox 8.1.5 — while BCM57414 (25G) works fine on same host with Like.
Hello everyone, I'm experiencing a recurring network failure on a Proxmox VE host using a Broadcom NetXtreme-E 100G NIC (BCM57504). The NIC stops transmitting, triggers a TX timeout, and then fails to reset correctly. After that, the interface...
-
SSunilkumar reacted to tomservo's post in the thread Making sense of NVMe zfs and SMART errors with Like.
I suspect that the upgrade changed something about the smart monitoring to reset the tracked stats, or maybe to start tracking stats that weren't tracked before. This is probably why it jumped from 0 to 12 or 0 to 16, and it's likely that you...
-
SSunilkumar reacted to jackdaw's post in the thread Making sense of NVMe zfs and SMART errors with Like.
Hope you’re all well. I have a question that’s been wrecking my head for months now. I have a 3 node cluster (Dell PowerEdge R7525) with the following drive configuration: Node 1: 10x 2TB NVMe KINGSTON SKC2500M82000G in raidz2 Node 2: 10x 2TB...
-
Ddaveanderson replied to the thread Broadcom BCM57504 (100G) bnxt_en TX timeout and NIC reset on Proxmox 8.1.5 — while BCM57414 (25G) works fine on same host./etc/network/interfaces contents: Basic gist is: two LACPs, each containing two of the ports, each nic has one port for each of the two LACPs (thus a nic card dying entirely should be ignored) of those two bonds: po7 / bond0 is for use by VMs...
-
SOVH Cloud https://eco.ovhcloud.com/de/soyoustart/
-
Shttps://www.vautron.de Nicht die günstigsten am Markt, dafür aber mit sehr kompetenten und engagierten Mitarbeitern. Individuelle Absprachen zu Hardware, Verkabelung, Serverstandort oder anderen Anforderungen sind jederzeit möglich. Domains...
-
SAls Tipp https://host-unlimited.de/dedizierte-server-mieten Schau mal rein.
-
SHallo Nachdem ich Hardwareprobleme mit einem Ded. Server bei Hetzner hatte und Hetzner die Preise massiv angehoben hat suche ich folgendes: Root Server für die Installation von Proxmox Kennzahlen: ca. 32 bis 64 GB ECC, 16 Cores, Raid 1 mit 2x...
-
SDouble post, please see the other thread: https://forum.proxmox.com/threads/pve-9-apparmor-errors.183926/
-
SAll of my upgraded hosts are throwing this error. No guests. No LXC containers. No nothing there. Just an empty, upgraded host. Throwing errors. [353827.192186] audit: type=1400 audit(1780020537.902:27110): apparmor="DENIED"...
-
SBios Update did the trick. There was one newer version available. After Update the Bios, everything is working, incl. Secure Boot. Thanks.
-
SVery annoying if a cold start works but a reboot doesn't! It seems that BIOS somehow doesn't find the harddisk or EFI partition after a reboot. To confirm; by going into the BIOS after a reboot you don't see the disk and the boot option there? I...