Setting up networking for ISCSI VLAN

[odesport]

Hi,
I've installed Proxmox V4.4 on a Dell blade serveur. I've managed to setup vmbr0 with bonding and VLAN :

auto lo
iface lo inet loopback

auto bond0
iface bond0 inet manual
slaves eth0 eth1
bond_miimon 100
bond_mode 1

auto bond0.49
iface bond0.49 inet manual
vlan_raw_device bond0

auto vmbr0
iface vmbr0 inet static
address 172.20.0.6
netmask 255.255.255.0
gateway 172.20.0.1
bridge_ports bond0.49
bridge_stp off
bridge_fd 0

But my simple VLAN for ISCSI doesn't see any host on the network :

auto eth2
iface eth2 inet manual
post-up /sbin/ifconfig eth2 mtu 9216

auto eth2.96
iface eth2.96 inet static
vlan_raw_device eth2
address 192.168.20.6
netmask 255.255.255.0
post-up /sbin/ifconfig eth2.96 mtu 9216

ifconfig shows :

eth2 Link encap:Ethernet HWaddr e0:db:55:24:5f:64
inet6 addr: fe80::e2db:55ff:fe24:5f64/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:9216 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:47 Memory:d3000000-d37fffff

eth2.96 Link encap:Ethernet HWaddr e0:db:55:24:5f:64
inet addr:192.168.20.6 Bcast:192.168.20.255 Mask:255.255.255.0
inet6 addr: fe80::e2db:55ff:fe24:5f64/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:9216 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:2758 (2.6 KiB)

It worked perfectly with Proxmox3. What should I do in Proxmox 4 ?

Thanks.

 

[AaronWalker]

https://pve.proxmox.com/wiki/Network_Model
https://pve.proxmox.com/wiki/Vlans

 

[odesport]

https://pve.proxmox.com/wiki/Network_Model
https://pve.proxmox.com/wiki/Vlans

I've read theses pages and followed the setup. That's why I'm writing on this forum.

 

[mir]

vlan_raw_device is not used anymore.

Rewrite to new syntax:
auto lo
iface lo inet loopback

auto bond0
iface bond0 inet manual
slaves eth0 eth1
bond_miimon 100
bond_mode 1

auto vmbr0
iface vmbr0 inet static
address 172.20.0.6
netmask 255.255.255.0
gateway 172.20.0.1
bridge_ports bond0.49
bridge_stp off
bridge_fd 0

auto eth2
iface eth2 inet manual
post-up /sbin/ifconfig eth2 mtu 9216

auto vmbr96
iface vmbr96 inet static
address 192.168.20.6
netmask 255.255.255.0
bridge_ports eth2.96
mtu 9216

 

[odesport]

Thanks,

Is it careful tu use bridge for iSCSI ?

 

[odesport]

I've applied your setup but vmbr96 is still isolated from the network.

 

[mir]

I've applied your setup but vmbr96 is still isolated from the network.

Isolated from which network?