pve-kernel-5.0.21-5-pve stuck on reboot/shutdown

[cj_duke]

Hi all,

after upgrading to pve-kernel 5.0.21-5-pve reboot/shutdown not working correctly.

cli (via ssh) -> shutdown/reboot ends in state where the system should either poweroff or reboot, but nothing happens, only hard reset possible. The state describes as blank monitor without signal, no disk usage, only fans spinning.
Loading pve-kernel-5.0.15-1-pve via grub menu -> everything works without problems. Same behaviour with fresh proxmox install only upgraded to latest.

Hardware:
ASUS M4A89GTD PRO/USB3 (Bios 3029)
AMD Phenom II X6 Black Edition 1090T

Thanks for your help.

 

[cj_duke]

Update 1: Tracked the issue down to the graphics card MSI R5770 Hawk. Removed the card, kernel 5.0.21-5 works, now using onboard HD4290 GPU. (Yes, I am aware R5770 is overkill for the system)

 

[ricardoj]

Hi,

Can you test WOL on your ASUS MB ?

Me and some other users are having a problem with WOL with Realtek NIC.

See this Forum message.

Thank you so much for your attention.

Regards,

Ricardo Jorge

 

[cj_duke]

Thanks Ricardo for your input.

Tested WOL with the ASUS/Realtek NIC, no success. I use a PCI adapater as well for link aggregation, WOL works on this one (for testing, no bonding used)

ethtool outputs:

root@pve: lspci
04:06.0 Ethernet controller: D-Link System Inc DGE-528T Gigabit Ethernet Adapter (rev 10)

root@pve : ethtool enp4s6
Settings for enp4s6:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: Symmetric
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000033 (51)
                               drv probe ifdown ifup
        Link detected: yes

root@pve: lspci
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)

root@pve : ethtool enp5s0
Settings for enp5s0:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: Symmetric
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000033 (51)
                               drv probe ifdown ifup
        Link detected: yes

 

[ricardoj]

Hi,

Thank you @cj_duke.

WOL is working again.

I just updated the previous Forum message.

Regards,

Ricardo Jorge