Edited 1/25/2023 - Now have it working!
Hello, I currently have a raspberry pi that connects to a VPN via wireguard, and then shares that connection with dumb hosts (like Rokus) via a VLAN and a dhcp server on it that forwards all traffic to the VPN. To do this I first set up a standard...
Hello,
I tried to configure my ProxMox but unfortunately I couldn't. I have try to make a bridge off wg0 but it's not working.
I would like to make a configuration so that the LXC containers have a public IPv4 address which is connected on the WireGuard client of the ProxMox server.
I have an...
I'm running PVE (pimox) on a Raspeberry Pi OS 64bit.
One VM is Home Assistant which runs Wireguard VPN add on. Wireguard works fine when i try to connect to local devices such as my router (192.168.1.1) or raspberry eth0 (192.168.1.136) but cannot ping vmbr 192.168.1.204 or connect to Home...
Hello,
I'm experiencing a pretty strange connection issue when connected to the second vpn VM (wireguard).
I got two proxmox nodes, each do have a VM with wireguard, a VM with a dns server, a VM with traefik proxy, both nodes have the same etc/network/interfaces files.
Both wireguard VMs are...
Hi,
I have been trying to setup Wireguard in an LXC Container on Proxmox using this Guide: Proxmox LXC Wireguard
It would seem though I have issue with Proxmox Networking or FIrewall.
The port ( as described in the guide and as I have configured, 51820) is not available publicly and the...
I would like to up a wireguard interface on the pve host, that will connect to the wireguard server in one of the lxc containers.
When trying to connect the PVE host via LAN or even via WAN IP to the container no proper connection can be established, no traffic is shown with "wg show" on the PVE...
Hello everyone,
I have installed straightforward Pfsense as VM on Proxmox. Everything runs as expected. But not the Wireguard access. I have prepared a S2S Wireguard tunnel between an external pfSense and those running as VM into Proxmox. However, the connection from my remote pfSense to the VM...
10.0.0.1 - VPS outside LAN
10.0.0.2 - VM inside proxmox with wireguard (within LAN)
192.168.1.112 - NAS without wireguard (within LAN)
Video: https://reddit.com/link/wp26ec/video/85rm42pn7wh91/player
10.0.0.1 <--> 192.168.1.112 bandwidth is throttling as show in my video (traffic routes...
UBUNTU-VM acts as a router to route traffic over wireguard (UBUNTU-VM is within a proxmox VE). NAS is an old WD EX2, which is not on wireguard, traffic from it passes through the proxmox UBUNTU-VM.
The problem is that bandwidth from NAS going outside to VPS is very slow, only 300KB/s (transfer...
I'll get my homelab setup later this week and I'll use proxmox for managing VMs and stuff.
One of the most important things I have to handle for my business is networking for my clients. To be more precise, unique gateways to access the internet.
I have been learning networking a lot lately...
Hi there,
I'm new to Proxmox and have it running (Virtual Environment 7.1-11)
I want to install Wireguard but didn't found anything that compares the 5 methods that I'm now aware of.
-on host
-in VM
-In LXC
-In Docker in LXC
-turnkey solution
The differences that I would like to know is...
Hi everyone,
i test the last days SDN on my cluster (v7.1-10, lasted updates) and detect some problem with VXLAN over wireguard.
The automatic create config is something like this for three nodes:
auto <zone_name>_<vnet_name>
iface <zone_name>_<vnet_name>
vxlan-id <vnet_id>...
I updated to the latest kernel, and basically once wireguard starts up in a nested container I get a page fault/panic.
Jan 20 14:07:08 pve kernel: [ 44.267836] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
Jan 20 14:13:24 pve kernel: [...
Hello everyone,
Wireguard is running on a LXC Container on my Proxmox-Server. In general, everything works as intended, but one particular "network group" poses an issue for me (my university's student dorms' networks).
On all of my windows devices I'm able to create a VPN tunnel, I'm however...
Hi, I am running Proxmox on a HP Thinclient T630. The internet connection of the server is 100down/50up but over both WG and OVPN I get maximum 23-25mbps either way. I tried them in both a VM and a LXC with no change. I played with the MTU from 1420/1500 all the way to 1200 - again no...
Hallo zusammen,
auf meinem Proxmox-Server läuft in einem LXC Container, Wireguard. Grundsätzlich funktioniert das System auch, ich hab jedoch Probleme in einer bestimmten "Netzwerk Art" (Studentenwohnheime meiner Uni). Alle meine Windows Geräte bauen zwar einen Tunnel auf, können doch danach...
Hi community,
i have created a hyperconverged ProxMox Cloud Cluster as an experimental project.
features:
using 1blu.de compute nodes: 1 Euro / month
using 1blu.de storage node 1 TB: 9 Euro / month
using LAN based on Vodafone Cable Internet IPV6 DS-LITE (VF NetBox)
the ProxMox cluster uses...
Hello!
I have VMs currently running on a Dedicated server at home and I also have VPS with a couple of IP addresses.
So I wanted to assign each KVM VMs (on the home server) a static IPv4 public address (from the VPS)
Anyone have ideas if this possible with WireGuard, OpenVPN?
If so, please...
Hello Proxmoxers,
I want to set up a WireGuard VPN from my home office to our small office. But before I can even start, I have to get networking up. Currently I can't even get my way out of the stock WireGuard container.
On the host in my home office there are 3 VMs and the newly created...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.