vlan management

Hi , I was looking to create two separate vlans, vlan100 for proxmox management and vlan200 for my vms. Ive been able to access my PVE host from another computer plugged to my managed switch with vlan100 on port 3 but ive not been able to get internet access with vlan200 for my vms . On my...

Have a small lab environment running with an NUC which have 3 different NIC's which: iface enp88s0 inet manual #Eth00: Intel I225-LM (2.5GbE) iface enx6c1ff7046396 inet manual #Eth01: Realtek RTL8156BG (2.5GbE) iface enx6c1ff704695a inet manual #Eth02: Realtek RTL8156BG (2.5GbE) And were...

In the process of putting together a plea for help as to how to get my cluster back together (copies of /etc/network/interfaces, /etc/hosts, /etc/corosync/corosync.conf for each of my 3 nodes) I found the mismatches and remembered to increment the config version up one. Now corosync is back...

So I am reconfiguring my proxmox setup, because I discovered a small problem that I have. I have a proxmox server connected with both 1gbit link, and a 10gbit link. current setup: - management is running on the 1gbit link, and NFS are also apperently running over this (server vlan) - vm's are...

Hello Forum I have searched the forum for an answer for about a month now, but I am unable to find one, or a similar solution to my problem. Recently I made the decision to migrate to Proxmox as hypervisor after using VMware since 2012. It goes very well. I’ve got an LXC container running and...

Hello. Is it possible to change Native vlan to something else than 1? If so, just globally, or is it possible to make it per VM?

Hi to the community, I am still in the learning hence ask for verification / help. Objectives: install pfsence on small, 2 NIC PS within Proxmox. Reason for the set-up: – the possibly to deploy another service on the same box (nginx); possibility to make pfsense snapshots before the upgrade...

Hello !! Do you know if it is possible to create Vlans on my pve, without going through a switch or other? Just creating from my GUI? I only have one physical network port.. I can't find much help on google.. Thank you in advance for the help provided :)

Hallo Zusammen , ich bin echt seit mehreren Tagen und Nächten am verzweifeln mit meinem neuen HomeLab. Obwohl ich viel hier und im Netz mich eingelesen habe, geht es in meinen alten Schädel nicht rein :( bzw., bekomme ich das als Newbie nicht umgesetzt. Daher bitte ich einmal um Eure...

Hello! I don't know if this is Proxmox or Mikrotik issue, but I've stuck with this for good. I'm getting VLAN ID from another location inside which are another VLANs, so we have QinQ here. All is delivered to rack cabinet, where Proxmox cluster is running. What I want to do is to strip...

Hello all, I am trying to setup VLANS on my Proxmox setup either by command line or using the web interface. Unfortunately i can't seem to get it functioning. All help would be greatly appreciated. Both Nic's are bridged to vmbr0. I plan on accessing the web interface on VLAN 1 and not...

Hi, as the title says i'm having a problem on VMs and containers that share the host pve VLAN. If the VM goes on a different VLAN, no problem. My intention is to have a bond between eno1 and eno2 with lacp layer 2 and have one bridge so every VM goes through that bridge with the specific VLAN...

Hello, I would like configure my manegement LAN on a VLAN 123 and also 1 virtual machine. when i configured if start up the server, its works.. but when i restart network or restart the server nothing work and can't access, i get the error in the attachemnd.. who can help me? I have...

Hi all, After some researching ive come to this solution. Here is my interfaces file. It contains 2 interfaces, one for managemento and another to service traffic. Hope it helps! ## interfaces file begin ## auto lo iface lo inet loopback iface enp3s0f0 inet manual #MANAGEMENT auto vlan666...