proxmox

Hallo liebe Gemeinde, ich bin in der Thematik recht neu was ProxMox angeht und arbeite mich die letzten Wochen immer mehr in das Thema ein. Aktuell sieht unsere Konfiguration so aus: 3x HP Server mit je zwei NICs a 2x SFP-Ports 1x HP ProCurve 4208vl Switch 1x Arista Switch Die 3 Server haben...

I’m looking for some guidance on expanding my Proxmox setup. Here’s my current setup and what I’m trying to achieve: Current Setup I have a dedicated OVH server running Proxmox. On this server, I have a pfSense VM that handles VPN access for employees to connect to the internal network. The...

Hi, I have tried to install Pfsense on Proxmox, but it's not even booting up. The installer always stops at bootup and does not move forward. I have changed the BIOS and added an EFi drive, but no luck. I also changed the machine type from Default (i440fx) to q35, but still no success. After...

Hi, I have taken over IT services for a private client, they have two Proxmox servers that the previous supplier installed, however, this supplier are not disclosing the username and password used to login. The servers are configured with the Proxxox OS on mirrored drives and all other data...

I have a new installation of Proxmox VE 8.3.3 and am using two external Drives for VM storage and backups etc. When I create a new VM, I start by highlighting the storage device I want PM to use when creating this machine. I make sure that the storage device I want to use is picked in the...

Hi Everyone, I'm new to Proxmox and recently ran into an issue with disk management. Here's the situation: I created an Ubuntu 24 server VM with an initial disk size of 150 GB. Later, I realized I needed to add an additional 25 GB, but I accidentally extended the disk by 175 GB, bringing the...

Hi Proxmox Community, I hope you're all doing well! I’m relatively new to Proxmox and have been exploring its features. I’ve successfully created and managed a few VMs, but now I need to clone one of them. My goal is to have the cloned VM operate independently with a different IP address. Could...

Hello, After adding the new node to the cluster, I installed ceph on it. Ceph installed itself with version 18.2.4, on the others it is version 18.2.2. I would like to do a ceph update on the other nodes. What is the safest way to do this? If there is data on osd's can it be done live or should...

Hallo zusammen, wir setzen in unserer Umgebung Proxmox als Hypervisor und Veeam als Backup-Software ein. Aktuell haben wir derzeit ein Problem, bei dem der Veeam Worker nicht korrekt funktioniert. (beim Starten bzw. Initialisieren) Backupjobs werden gestartet, allerdings wird der Veeamworker...

Wiki for reference: https://pve.proxmox.com/wiki/VNC_Client_Access I'm looking into adding this to some of my VMs to make them more accessible. However, I'd like to isolate the VNC network from Proxmox MGMT in general. I've run into a few issues so far, and I'm not quite sure the best...

Ich habe kürzlich einen Dell R940-Server gekauft, dessen Spezifikationen wie folgt sind: CPU: 4x Intel Xeon Gold 5118 (12 Kerne, 2,3 GHz) RAM: 768 GB DDR4 (2133 MHz, verteilt auf 24 DIMM-Slots) Chipsatz: Intel C620 GPU: Intel Arc A380 Das Problem tritt auf, sobald ich eine VM...

Hallo erst mal, ich bin der Neue... Mein alter Server hat den Geist aufgegeben und nachdem ich in den vergangen Jahren verschiedene Lösungen für meinen Sever zusammen gebastelt hatte, nutze ich den Storage Controller Ausfall, um alles mal aufzuräumen. Das Problem ist, dass ich da eine...

Uploading a iso via wired ethernet connection by gui stopts around 10%. After that if you abort and try again it's les then 10% and after that even less and so for until iets 1% I searched this forum and found a small solution, using sftp with filezilla, it works, but very slow, after every 5%...

Hey all. just made a fresh install of all my nodes, and i got a strange problem i have never seen before. Quick info: Nodes Prox1, Prox2. Prox3, Prox4, Prox5, Prox6 is my name on the nodes. and ip for each node is: 192.168.100.201, 202, 203, 204, 205, 206. when i log on to Proxmox web gui i...

Hi, i've installed opnsense on my proxmox and used 2 LINUX bridge port which is assigned on my X550-T2, the issues is that the LAN port is set to use 1G due to being plugged on my 1GB switch while my WAN gives me 2.5G how can i use the 2.5G in my VMs. Because using the LAN bridge only gives me...

Hello, I am in the process of migrating some LXC containers from one host to another where I have different types of storage. The source host where the container is located has ZFS storage and the destination host has XFS (LVM). How should I proceed? I have tried to make a copy of the...

Hello, I have the problem that after a random time the server simply freezes, all websites and ssh accesses and also the command line on the server with a vga screen freezes I'm new with proxmox I runned 1vm with Debian and a Minecraft Server i don't knew because it is randomly maybe after 1Min...

Titel: Ceph: Nur HDD für data-Pool und SSD für nvme-Pool verwenden Problem:Ich möchte in meinem Ceph-Cluster (Proxmox) sicherstellen, dass: HDD-OSDs nur im Pool data verwendet werden. SSD-OSDs nur im Pool nvme verwendet werden. Aktuelle Situation: OSDs: ID CLASS WEIGHT TYPE...

Hello everyone, I’m currently setting up my first Ceph mirror configuration and have a few questions regarding its behavior. For example, I’m uncertain about how to force-promote an image on my DR cluster (site-b) during the synchronization process. From what I’ve read in the documentation, in...

Hi , I just added second nvme 1Tb to proxmox server. System boots up norammly no beeps no issues. However when it reached to proxmox screen for roo password it stays there for few seconds then goes blank and stops. I also notied the attched LAn card also do not blink at all. However once i...