10g

Hi, I have virtualized the opnsense and pass-through QLogic NetXtreme II BCM57840 via iommu. I can't get both the ports work, one of them works but the other has the problem with the address mapping. I am just wondering if someone else has faced the same problem, the logs are as follow, please...

I have a Qotom router with Intel(R) Atom(TM) CPU C3758R @ 2.40GHz. It has 5 2.5G ports, and 4 10G SFP+ ports 04:00.0 Ethernet controller: Intel Corporation Ethernet Controller I226-V (rev 04) 05:00.0 Ethernet controller: Intel Corporation Ethernet Controller I226-V (rev 04) 06:00.0 Ethernet...

So, as the title says, I am deploying all new Proxmox servers to replace our aging fleet of 2U Dells. Currently, I have a 10G trunk for all of my normal VLANs and a separate 10G connection specific to only Corosync VLAN traffic. My new servers have 4 x 10G NICs and 2 x 100G NICs each. I was...

I am trying to get my 10G NIC to show on the PVE. however I only have one, the onboard 1G connection. root@pve:~# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet...

Hello, I'm running PVE8.0 at home. Multiple users working from home with Windows VMs. Many small Linux VMs doing lots of low-bandwidth stuff. I'm in the process of setting up a 3-node cluster for HA. All 3 nodes have identical hardware. All 3 nodes are on a 10GB fiber network. All 3...

Hi guys! I need some help with a 10G NIC. A client was running a new server and the 10G appears on the web interface, but in the console not. How can i try to "install" this NIC in this server?

Hi, first off, sorry if this is in the wrong category. I am kinda new to Proxmox and Linux in general but find it really useful, so I started tinkering a bit. I have a Windows 10 (main workstation) and a "home server", an E5-2678V3 on a dual socket Chinese board. My server is running a TrueNAS...

Hello, Apologies if this topic was covered elsewhere, I just could not seem to find the topic in the search. About a month ago I installed not upgraded, installed fresh Proxmox 7.0 and all was fine until I decided to virtualize a plex server using Ubuntu server 20.04 with my Nvidia 1660 for...

Preface: I am not a linux/unix guru, but I can figure things out and googlefoo for the most part... I've only added the components of my network that are valid for this post. Configuration: *Server 00 2x Xeon E5-2678V3, 256GB ram, Intel 540-T2 10 GbE, Intel I350 2x 1GbE and onboard 540-T2 GbE...

Hi! I’m trying to take advantage of a 10G Mellanox ConnectX-3 EN (running the most recent firmware version, 2.42.5000) installed in my Proxmox (5.2) to utilize the full 10G bandwidth between Proxmox and a seperate FreeNAS (11.1) box and I’m running into trouble. My Proxmox host (pve) is on an...

I was wondering wether someone managed to build ixgbe drivers for the current Proxmox 4.4. When I try to build the driver, I get an error: make[1]: Entering directory '/usr/src/linux-headers-4.4.62-1-pve' CC [M] /root/ixgbe/ixgbe-5.1.3/src/ixgbe_main.o In file included from...

So there is a howto on the wiki that details the setup of a 10 Gbit/s Ethernet network without using a network switch: http://pve.proxmox.com/wiki/Full_Mesh_Network_for_Ceph_Server If I understand correctly, you would need a two port 10 Gbe NIC (or two NICs) in each of your nodes, you connect...