Search results

I have tried all of them. The network seems to have completely disappeared. All the unifi switches are in offline mode now. I think if there is a clean way to roll back, I'd like to do that an wait this out.

How can I rollback to v7? My network has been messed up on v8 and not getting anywhere to resolve it for a couple days now. Now, I cant even access the GUI anymore. Was available yesterday. Nothing has changed.

@Spoonman2002 Here: auto lo iface lo inet loopback iface enp10s0f0 inet manual iface enp10s0f1 inet manual iface ens4 inet manual auto vmbr0 iface vmbr0 inet static address 10.1.5.33/24 gateway 10.1.5.1 bridge-ports enp10s0f0 bridge-stp off bridge-fd 0 auto vmbr1 iface...

I upgraded to proxmox 8 last night. All my VMs now can't get an ip adress from the dhcp server. Not sure how to troubleshoot this. Other appliances on the home network get ip addresses just fine.

Got the same error message. How do you install systemd-boot ? Can i just install it with apt install systemd-boot ? Do i need to configure anything after that? Just want to make sure I do it correctly. btw, all my vms are not able to get ip addresses from the dhcp server anymore. not sure if...

@LnxBil I tried this route and got quickly lost with setting up a k8 cluster - way too complicated for me. And concerned about how to even troubleshoot if something goes wrong. Won't know where to start ! I could have used k3s. I have also recently being trying my hands at a hashicorp nomad...

I can't decide if its better to have a dedicated vm for each docker app install or just create one gaint vm to hold all docker containers ? Most of the discussions I have seen are centered on the merits of installing docker in an lxc or vm. I have decided to go the vm route. What are the...

I want to passthrough a dedicated 10G nic port to my truenas scale setup. I typically setup the static ip address by mapping a mac address to the static ip in my dhcp server. Not sure how this will work with the passthrough nic. I know the mac address of the NIC port. However, not sure where...

Done! I have just 8 nvme drives so didn't take too much time. I assumed I could add them via the extender. Using this method, I see the disks listed in both truenas and proxmox. Isn't that a problem? I wonder if Its better to add another controller in an available PCIe slot and connect all...

Yes, everything is ok ( for the sas drives). Not the nvme drives attached to the extender devices.

@leesteken - you mean pass each individual hard drive separately? What do you mean by "device"? I can't see any of the PLX devices in the dropdown list

Hello I have a Dell R740 server which has a PCIe backplane extender for nvme drives. I am looking to passthrough the extender to a truenas install . When I go to add PCIe device for the truenas vm, I don't see the extender listed though I can see it when I do an lspci on the proxmox node...

@aaron How about something like dell idrac service module ( ISM), which depends on the installed OS. Mine is not working with proxmox installed as the OS on the server.

I recently got a Dell PowerEdge 740xd which came with an enterprise lifecycle controller license and a boss card. I installed proxmox on a dell boss card. However, I am finding that I am not getting the full functionality of the lifecycle controller without installing an approved OS for the...

Are there any guides how to do this? Apologies, this is a bit over my head. Learning.

Do I need to do anything in postgres to make sure the data is saved on the new virtual disk? Which disk type do I use ? SCSI, VirtIO, SATA, IDE ? I am looking to use the ZFS storage drive I have on the proxmox machine.

Can you point me in the right direction how to do this? I will stick with the VM

Thanks for that link. It was helpful. But I am missing how I can assign and connect storage to the postgres VM. I have done the following so far: zfs create databank/db -o mountpoint=/db zfs set quota=48G databank/db # create one dataset for every database zfs create databank/db/db01-pg14...

Hello @LnxBil - Apologies for reviving an old thread. I have a question related to our discussion above. This time around I am looking to setup my postgresdb with storage directly on a zfs volume I have on my proxmox server. The postgresdb is setup on an ubuntu 21.10 VM. How do I assign...

no reference to bridge-ports eno1.5 and iface eno1.5 inet manual ?