The ethernet frames from the VM come from the tap adapter. The VLAN tagging of these frames happen when the packets are processed by the bridge, You can see the vlan tag with :
bridge vlan show dev tap100i0
port vlan-id
tap100i0 444 PVID Egress Untagged
When i do "systemctl status multipathd" I am getting:
multipathd[3683]: sdbd: path wwid has changed. Refusing to use
What does this mean? Any ideas what might be causing this?
Hi all,
I am once again in the dire situation where one proxmox node has problems with one multipathed iscsi device and it stopped responding to lvm commands which are stuck forever. I have tried many things to restore the iscsi device but I haven't managed to do it.
The question is if there...
Well this tend to be funny:
I did a "ceph osd set-require-min-compat-client luminous" which allowed OSDs to be able to rebalance and then a "ceph osd reweight-by-utilization" to make it rebalance OSDs. The result was:
Before:
ID CLASS WEIGHT REWEIGHT SIZE RAW USE DATA OMAP META...
Well, I chose 2/1 because I usualy see raid5 for SSDs on enterprise storages, but Ok, your comment is noted (about the 3/2 size/min_size).
I have only one pool on the ssds, so the target_ratio should really be 100%.
The output in my posting was part from the "ceph osd df tree" command.
Now...
Hi all,
I have a setup of 3 proxmox servers (7.3.6) running Ceph 16.2.9. I have 21 SSD OSDs, 12*1.75TB,9*0.83TB. On these OSDs I have one pool with replication 1 (one copy).
I have set the pg_autoscale_mode to 'on' and the resulting PGs of the pool are 32.
My problem is that the OSDs are very...
Well yes, forums are full of advise for ceph/zfs that OSDs/disks should rely on local storage.
While both ceph/zfs are built with the assumption of local disks for perfectly valid reasons, you can always remap these reasons to your environment, take your risks and create something that suits...
HI all,
I have a dozen MD3800i 100TB storage arrays that I can reach over 10G iscsi.
I would like to create ceph OSDs on these 100TB iscsi disks in order get the best of Ceph's redundancy (replication etc) for backup purposes.
When I try to create the OSD, it fails:
#pveceph osd create...
Hi all,
I have a VM that runs a passthroughed ethernet x710 adapter with dpdk (danos). Since dpdk does polling, the CPU is occupied 100% all the time. So, i would like to pin specific cores to this VM (in proxmox), in order to disallow the host task scheduler to change the association of the...
Hi all,
I would like to upgrade my cluster from 6 to 7 and at the same time I would like to upgrade the hardware (replace the servers with new ones). Now, I have 3 nodes with pve6.
I am thinking of installing the 3 new servers with pve7, adding them to the cluster and then removing the old...
Hi all,
We have recently upgraded proxmox from v6 to v7. I noticed some warnings on the Updates/repositories page and I have a few questions.
- I don't have a subscription but i have the no-subsctiption repo enabled. I get a warning that the no-sub repo is not production ready.
- If i disable...
Well, indeed on of the servers includes the domain in the hostname (px1.xxx.com) but after i chnaged it, and restarted the mon on px1 the problem was not solved. Now after a few tries the mon does not run. The config files are the same as before but the ceph-mon does not run.
Any ideas on how...
Hi,
I tried with a clear cache and the output is the same. The output section of your command that has to do with the mons, is this:
"mon" : {
"px1@px1" : {
"direxists" : 1,
"service" : 1
},
"px1@px1.xxx.com" : {
"addr" : "10.11.20.129:6789/0"...
Hi all,
I upgraded my cluster from v5 to v6 and now I want to upgrade ceph from luminus to nautilus.
The problem is that the proxmox gui shows one cluster member two times, as you can see in the attached picture.
ceph cluster heath is:
ceph health
HEALTH_OK
root@px1:~# ceph status
cluster...
Hi all,
When I do upgrades to proxmox or other actions that jeopardise the clusters health (network stuff), I feel the need to disable the cluster/watchdog/fencing components of promox, in order to do the actions without the danger of a node rebooting because it was fenced.
So, what is the...
Hi all,
I did a "pvecm delnode hp4" and removed a node from the cluster. Everything looks fine. The only problem i got, is that i don't contol the removed node....
So if someone boots the node, it will come back online and as the documents state:
"it is critical to power off the node before...
Hi all,
I have a 3 node proxmox cluster with pve6, on HPE DL380gen10 hardware. I had just upgraded from pve 5 to pve6, so i was checking things. At some point I noticed that one node had wrong time and it was 10minutes behind. I added an ntp server and synced the time.... Immediately the server...
Hi all,
I am on Proxmox 5.4.6 and I did a passthrough of an Intel x710 adapter to a VM. The adapter had a interface name on Proxmox (enp59s0f0) and after the VM started, the adapter was removed from Proxmox.
I have two questions:
- Now I have stopped the VM and I have removed the passthrough...
Hi all,
I would like to convert an LVM based disk to VHD format.
I have done it successfully by getting a backup (vma.lzo) and then decompressing it, extracting it and converting it (qemu-img convert).
I woud like to do this in fewer steps. So, I have the following questions:
- I though of...
Hi all,
There is an option to select NUMA when you configure a VM's CPU. While I know the basic NUMA concepts, I don't really understand what this checkbox does.
So, I have a few questions about it and an application that might benefit from enabling NUMA.
Starting from the App, I have a VM that...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.