Hi,
I'm running proxmox on this Board: https://www.supermicro.com/en/products/motherboard/A2SDi-12C-HLN4F
CPU: Intel Atom Processor C3858
RAM: DDR4 RAM Rdimm 2666MHz ECC
In my vm settings i wan't to use the host directly as CPU-Type.
But when I'm starting the Debian VM I'm getting the...
Hi,
i did a fresh proxmox-install on a SSD.
If I run pveperf I get the following result:
root@pve:~# pveperf
CPU BOGOMIPS: 179207.68
REGEX/SECOND: 3038160
HD SIZE: 28.91 GB (/dev/mapper/pve-root)
BUFFERED READS: 522.68 MB/sec
AVERAGE SEEK TIME: 0.08 ms
FSYNCS/SECOND...
Hi,
I'm trying to passthrough my AMD RX 5500 XT to an Win10 VM.
The VM is throwing Error Code 43 in the VM-device manager and my host posts the following message on VM-bootup:
Is it OK that the video/audio iommu group is different (38/39)?:
My config:
bios: ovmf
bootdisk: virtio0
cores: 2...
Hi, are there any plans to put the fix into the proxmox kernel?
https://forum.level1techs.com/t/navi-reset-kernel-patch/147547/47
I'm trying to passthrough a amd 5500XT but I have no luck and get issues with "iotlb_inv_timeout".
My motherboard: Supermicro H11SSL-NC with an amd epyc 7282
Thanks!
Hi,
my setup:
Proxmox: 6.1-5
Board: Supermicro x10sl7-f with Xeon 1230v3
GPU: Radeon 5500 XT --> GPU-VM
SAS-Controller: Onboard --> Storage-VM
GPU-VM is Windows 10
Storage-VM is debian
I can't use both pcie devices at the same time. After a while the GPU-VM is going into suspended mode in...
Hi,
I'm getting the the following error at startup:
"Failed to start Raise network interfaces at boot up"
/etc/network/interfaces looks like:
auto lo
iface lo inet loopback
iface eth0 inet manual
iface eth1 inet manual
auto vmbr0
iface vmbr0 inet static
address 192.168.20.200...
Hi there,
since my upgrade to debian stretch i get the following issue with a usb smartcard reader:
Nov 13 21:13:32 proxmox kernel: ohci-pci 0000:00:13.0: frame counter not updating; disabled
Nov 13 21:13:32 proxmox kernel: ohci-pci 0000:00:13.0: HC died; cleaning up
Nov 13 21:13:32 proxmox...
Well... I have a big big problem... what I just did was an apt-get update and apt-get upgrade...
There is/was an error at the end:
root@proxmox:~# apt-get upgrade
Reading package lists... Done
Building dependency tree
Reading state information... Done
Calculating upgrade... The following...
Hi there again,
what should I have to do to control a VM, which has a dedicated GPU, remotely via noVNC (which comes with proxmox)?
I'm getting a black screen when I use the noVNC Console. So I think the VM is trying to display the screen via the GPU.
Thanks!
Hi there,
i want to passthrough a NVIDIA 1050ti. If I follow the instructions in the Proxmox Wiki using the OVMF Bios I get the following error when I start the VM (Windows 10): "failed to get group 1"
Should I re-activate the "pcie_acs_override=downstream" - Patch in the grub? Or is there...
Hi there,
I want to pass a Nvidia GPU to a Windows 10 machine.
I know there are some issues with Nvidia regarding pci passthrough.
How can I set special parameters like "hv_vendor_id=whatever" etc... just in the vm config file?
Thanks!
Hi there,
i would use my BluRay Player to pass it through to my "Windows 7" - Guest-OS to rip BluRays there...
In short: It doesn't work!
If I open the drive in the Guest-OS nothing happens and it's loading to death...
Are there any other opportunities to use the drive in my Guest-OS?
thanks!
Hi,
next issue with proxmox... ;)
I map a USB Sound-Box (Multi-Channel 7.1) to a Windows VM.
I can see the USB Device in the VM but if i install the drivers the VM crashes... i lose the network connection... even the ssh connection to proxmox, but i can reach the webgui of proxmox. If i stop...
Hi,
i have a problem with port mapping my usb3.0 port to a vm.
USB2.0 works well!
qm monitor shows that the vm recognize the usb port, but in the vm (debian wheezy) itself it doesn't show up.
There is an "enumerate" error on the host... what's about this error?
Here are the screens of the...
Hi,
is it possible to update a HDD firmware in a VM when the Sata-Controller is connected via pci passthrough?
What i wanna do is this:
http://support.wdc.com/product/download.asp?groupid=609&sid=113&lang=en
boot to dos and then execute the exe file... Will it work?
Hi there again,
after solving the most problems regarding SAS-Controller PCI-Passthrough i got a new challenge:
PCI-Passthrough of a GPU. For the first look everything looks nice. The Card is shown up in the VM, but after installing the driver (installation says "successful") and rebooting the...
Hi,
i got a new Board (Supermicro X10SL7 with LSI 2308 SAS Controller (disabled on boot)).
After grub ist starting proxmox i get this error:
But proxmox is reachable by Web-GUI!
If i enable the LSI Controller the same error occures.
Some idea?
thanks..
Edit:
Even if i passthrough the...
Hi there again.
I did the pveperf test:
CPU BOGOMIPS: 10376.46
REGEX/SECOND: 1193260
HD SIZE: 7.14 GB (/dev/mapper/pve-root)
BUFFERED READS: 64.46 MB/sec
AVERAGE SEEK TIME: 0.29 ms
FSYNCS/SECOND: 102.64
DNS EXT: 90.72 ms
DNS INT: 1.19 ms...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.