Search results

@spirit I will try your suggestions. I am still setting it up so it is not in production yet. I am doing all my testing on test VMs. So restarting will not be a problem. Thank you. @tschanness I can increase the ram. I will give it a shot. all nics bonded. However, doesn't increase...

@czechsys I would be happy if it was 150MBps, it is much less than that. ~23MBps for bs=1M count=1024 What is the best performance network storage for Proxmox? I thought it was Ceph... Hardware below, Dell R210 CPU: 8 * X3460 @ 2.80GHz Mem: 4GB HDD per Ceph node: 8 Network: 2 nic bond cat 6...

The setup is 3 clustered Proxmox for computations, 3 clustered Ceph storage nodes, ceph01 8*150GB ssds (1 used for OS, 7 for storage) ceph02 8*150GB ssds (1 used for OS, 7 for storage) ceph03 8*250GB ssds (1 used for OS, 7 for storage) When I create a VM on proxmox node using ceph storage, I...

I have the same problem. Nov 30 11:18:09 pmox03 pveproxy[16239]: problem with client 192.168.1.10; ssl3_read_bytes: tlsv1 alert unknown ca Nov 30 11:18:09 pmox03 pveproxy[16239]: Can't call method "timeout_reset" on an undefined value at /usr/share/perl5/PVE/HTTPServer.pm line 315. Nov 30...

Only when I open clustered Proxmox GUI on web browser, https://IP:8006 I see errors on only 1 of the servers below. Nov 30 11:18:09 pmox03 pveproxy[16239]: problem with client 192.168.1.10; ssl3_read_bytes: tlsv1 alert unknown ca Nov 30 11:18:09 pmox03 pveproxy[16239]: Can't call method...

I have a 3 node ceph proxmox cluster for storage with node1 7*143GB ssds, node2 7*143 ssds, node3 7*218 ssds. Now I have read through the http://docs.ceph.com/docs/jewel/architecture/#mapping-pgs-to-osds however it is not 100% clear to me if I can create a VM with hard disk size 300GB using Ceph...

I have a Ceph and Proxmox running without any problems. Now considering future scenarios such as running out of space on current Ceph cluster. 1. Creating a new node with drives, adding to the already existing cluster makes sense. However, how do we add the new drives in the new node to the...

Thanks for the reply Ashley, It was indeed the switch which was not tagged for all the vlans. Once they were tagged and vlans were defined in the interfaces file, it all worked well with vmbr from those vlans. Best,

Hi All, I have been trying to configure bond0 with 4 nics but I had no luck so far. Below is the /etc/network/interface file auto lo iface lo inet loopback iface eth0 inet manual iface eth1 inet manual iface eth2 inet manual iface eth3 inet manual auto bond0 iface bond0 inet manual slaves...

This is excellent Tom, thanks a lot. I m sure it will be helpful to many of us experiencing similar problem. However, I have already upgraded the server to the latest 3.3 and I have not experienced the same issue since the upgrade. It has been 4 days since upgrade and memory usage and allocation...

Here is the give ram amount to each kvm. I have several of them so i dont think it is only one server's fault. None of them run at 100%, three of them usually average at 90 - 95 percent, and others are usually around %70. After restarting the whole server, the problem doesnt happen for weeks or...

There is no additional software running on the server. Clean installation of 3.2 proxmox. Below is the output of "top". And I am certain that memory allocated by me for those 9 servers are not higher than 5GB. However, as I can see from "top" command they consume more Ram than allocated for...

any idea on this memory leak?

I have 9 KVMs running on Proxmox 3.2 and total of 5G of ram given to 9 KVMs. Proxmox server has 8GB of ram and 7GB of SWAP. For most of the time when i check summary of the server i see that it uses all 7.50Gb of ram and all 7GB of full SWAP. Well that is bad for multiple reasons. I can not run...

I dont think my problem on the original post is the same problem as we see here. I dont have any bounded interfaces and it was working without any problems before. So as for http://forum.proxmox.com/threads/17598-vmbr0-port-10(tap109i0)-entering-disabled-state problem, then what is the...

This can not be good. I have too many disconnects from ssh clients. Below started happening in kernel log recently ~~ 2weeks. The system was at 3.0. when the first time it started happening. Updated to 3.1 no change. It was working beautifully for over a year :( Any idea how to solve this issue...

Very simple question... Without enterprise subscription, now running 3.0. They will roll out 3.2. Can't I simply upgrade to 3.2? Also assume 3.2 got to be stable when they put on their site for Download, yes?

What i understand is the following: pve-enterprise will get bug fix updates and such. Then what happens when I am running 3.0-20 version and I want to upgrade lets say 3.2 when it is out? Technically I can download it for free but I can not upgrade from 3.0 to 3.2 for example? "Beginning...

"We are just afraid of possibility, that the next new versions and bugfixes are going to be only for pve-enterprise subscribers." is that the case?

Good Day, I m seeing a wierd pattern when i take a backup of one of my KVMs. I used to have over 40G of data in that kvm centos, then removed all those files/folders not there is only 1G of data in that server. I took a backup of that kvm on proxmox and it took forever and i see that the...