Search results

ok, this is clear Please still bear with me still something I'm struggling to figure out properly here. Please let's go on by making some examples 1) I'll passthrough the second NIC. What happens to the swith or any PC connected to the second NIC? Can they acces internet as they do before...

ok, I need to make sure that I'm getting it right I don't think I got exactly what is going to happen to VMs in proxmox if I passthrough the NIC. Would the same physical devices connected to the same NIC still have access to the LAN and get their IPs from pfsense? Internal VMs won't have access...

Hi, Ok, I have to post the same images one more time :): this is my network setup in Proxmox: LAN and VLANs in pfSense: The Proxmox's VMs are connected via vmbr1 to VLAN1 (192.168.10.0/24) If I plug any device to the enp5s1 NIC it goes on LAN (192.168.5.0/24) and gets its own ip...

Hi, I installed pfSense as a VM in Proxmox, then I plugged a dd-wrt device to the second physical NIC . I use the first one to access Proxmox and pfsense via WAN as well. for more details about my configuration you please have a look at my previous thread here...

UPDATE I FIXED IT FINALLY. It was the Windows' Firewall.

This is strange. I restarted all my devices this morning, I tried it again, and it turned out that I can now open a Remote Desktop session from my external PC to my Windows VM in Proxmox in VLAN10, but I still can't ping it!

Ok I think I got it right ...for the most part at least. In order to make it as simple as possible, I decided to create two VLANs only I set up VLANs in pfSense first: then I tagged a VM's network device (My Windows VM in Proxmox in this case): For VLAN10, I set 192.168.10.0/24 as its...

ok According to my goal, as for pfSense only, do I need to delete LAN interface and add only VLAN interfaces? Please see image four. Thanks

I dont' think I have understood option 2..anyway I'll most likely go for option 1, but I need to make sure that I got it right. So, when I enable "VLAN aware" on the virtual bridge (vmbr1) it would be as if I had set up a trunk port for my VLANS? Correct? Are you talking about the PHYSICAL...

Hi, For the time being, I've installed pfSense in Proxmox as a VM. Here is the diagram: On NIC1 is my WAN connected to my ISP router in, say, DMZ Here is my Proxmox network setup: In pfSense the two virtual switch are seen this way: Basically the LAN above with IP 192.168.5.1 manages...

I'm not sure what you mean with current state. Did I save the "NOW" configuration? In that case it would be ok since I saved the "after unbound" configuration before removing it. Thanks again

I did a backup of the "after_unbound" snapshot and put the file elsewhere, so I think I saved the last configuration this way. I think that I'll remove the more recent snapshot as you says. Anyway It would have been much easier getting back "on the fly" to a previous snapshot. I didn't know...

it is probably my fault because it is likely that I haven't yet understood how the rollback in Proxmox works. I tried to rollback to a previous snapshot of a LXT (before_unbound): But after I ran it I got this error message: So, how can I possibly get back to a previous configuration I...

Same VM (pfsense) running at the startup before and after I upgraded to V7

Ok, but I didn't make any changes to my configuration and VMs, nor added new VMS. I haven't understood why there wasn't any TAP device in the list before I upgraded to Proxmox 7. Thanks

Hi, I upgraded to Proxmox 7 and averything seems to be ok. Anyway, I ran the ip -c link command and I now see to new network items in the list: .... tap102i0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 tap102i1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 They both have their...

Could it be a problem with the VM backup itself?

Hi, I had a problem with my zfspool, and had to replace a disk. I took that chance to turn my 3-disks zfspool from RAIDZ into "mirror" with only two disks (it's a just little home lab I use to practise). it seems that everything went well, and I started restoring my VMs from my backups. The...

So, I should destroy and recreate my VMs and it added disks if I want to change the volblocksize? Thanks

It is set on 8K. But I read on the excel sheet that it wouldn't make any difference with a zfs pool made of 3 disks . By the way, what is the difference between the "RAIDZ1 PARITY COST, PERCENTAGE OF TOTAL STORAGE" sheet and "RAIDZ1 PARITY COST" sheet? I think I got it now, thanks Last thing...